EasyManua.ls Logo

JLG X390AJ-X14J - User Manual

JLG X390AJ-X14J
107 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Supplement Manual
Models
X390AJ-X14J
X550AJ-X19J
X700AJ-X23J
X370AJ-X13JP
X430AJ-X15JP
X500AJ-X17JP
X600AJ-X20JP
X770AJ-X26JP
X1000AJ-X33JP
*See inside cover for serial break
information
31215460
October 14, 2019
Go to Discount-Equipment.com to order your parts

Table of Contents

Questions and Answers

  • O
    osalazarAug 17, 2025
    What to do if my JLG Boom Lifts battery charger shows error code 252 (short-circuit in output)?
    • C
      chenanneAug 17, 2025
      If the battery charger displays error code 252, indicating a short-circuit in the battery charger output, turn off the battery charger and resolve the short-circuit at the output.
  • B
    bakerbradleyAug 20, 2025
    What to do if my JLG Boom Lifts battery charger shows error code 244 because the mains voltage is too low?
    • J
      Joseph MeltonAug 20, 2025
      If the battery charger shows error code 244, indicating that the mains voltage is lower than the maximum operating range tolerance, make sure the mains voltage is within the correct operating parameters. The battery charger won’t start charging until the mains voltage returns within the normal operating range.
  • M
    Michelle MooreAug 22, 2025
    What to do if my JLG X390AJ-X14J battery charger shows error code 240 because digital input is open?
    • D
      Daniel PowellAug 22, 2025
      If the battery charger displays error code 240, indicating that the digital input is open, the battery charger will stop charging until the digital input closes. Close the digital input to resolve this issue.
  • J
    Jenna HawkinsAug 25, 2025
    What to do if JLG X390AJ-X14J Boom Lifts show Inverter Error Code 8 - Watch Dog?
    • A
      April MyersAug 26, 2025
      If the JLG Boom Lifts shows Inverter Error Code 8 - Watch Dog, check the control connections and continuity of the electric motor. If they are OK, replace the inverter, because the inverter is not able to activate or turn off the electric motor.
  • D
    dkentAug 27, 2025
    What to do if JLG Boom Lifts show Inverter Error Code 19 - Logic failure #1?
    • M
      Michael JohnsonAug 28, 2025
      If JLG Boom Lifts shows Inverter Error Code 19 - Logic failure #1, it is usually a temporary anomaly due to a working condition, caused by an overvoltage or a sudden voltage drop. However, if the anomaly persists, replace the inverter.
  • T
    Troy MclaughlinAug 30, 2025
    What to do if JLG X390AJ-X14J Boom Lifts show Inverter Error Code 16 - Aux output KO?
    • S
      Sandra WhiteheadAug 30, 2025
      If JLG Boom Lifts shows Inverter Error Code 16 - Aux output KO, it is usually a temporary anomaly due to a working condition, caused by electromechanical brake problem. In case the anomaly persists replace the inverter.
  • M
    Mallory WebbSep 2, 2025
    What to do if JLG X390AJ-X14J Boom Lifts show Inverter Error Code 8 - Flash Checksum?
    • D
      Devon DixonSep 2, 2025
      If JLG Boom Lifts shows Inverter Error Code 8 - Flash Checksum, replace the inverter, because the software is corrupted or the inverter is damaged.
  • K
    Kenneth RodriguezSep 5, 2025
    What to do if JLG Boom Lifts show Inverter Error Code 13 - Eeprom KO?
    • R
      Raymond ColeSep 5, 2025
      If JLG Boom Lifts shows Inverter Error Code 13 - Eeprom KO, replace the inverter, because there is a hardware or software problem in Eeprom.
  • C
    Curtis NelsonSep 7, 2025
    What to do if JLG X390AJ-X14J show Inverter Error Code 18 - Logic failure #2?
    • Q
      qparksSep 7, 2025
      If JLG Boom Lifts shows Inverter Error Code 18 - Logic failure #2, replace the inverter, because there is a fault in the inverter.
  • J
    Jennifer VelazquezSep 12, 2025
    What causes BMS fault code 02 - Unexpected Voltage in JLG Boom Lifts?
    • W
      Wendy MercerSep 12, 2025
      BMS fault code 02, "Unexpected Voltage," in JLG Boom Lifts is caused by the BMS failing to identify one cell or being unable to connect it to the discharging resistance. When one cell reaches 3650 mV, the BMS will disconnect the lithium pack, triggering this error.

Summary

SECTION A. INTRODUCTION - MAINTENANCE SAFETY PRECAUTIONS

General Introduction

Details the Lithium ION system and safety precautions for machine operation.

SECTION 1 - SPECIFICATIONS

1.1 Capacities

Details Lithium Systems and Cell Features for various models.

SECTION 2 - SERVICE PROCEDURE

2.1 12 V DC Power Distribution

Explains the 12V power system, its components and function.

2.2 Operation of the Power Pack Components

Describes how the power pack components interact and function.

2.3 Battery Management System (BMS)

Details the functions and importance of the BMS in monitoring and managing the battery pack.

2.4 Lithium Battery Cell

Provides characteristics and specifications of individual lithium battery cells.

2.5 Cooling System

Explains the function and operation of the battery pack's cooling system.

2.6 Heater System (3 rd Generation)

Details the heater system for 3rd generation battery packs.

2.7 Lithium Ion Battery Pack Charger

Explains the function and operation of the battery pack charger.

2.8 Relays

Describes the function and purpose of various relays within the system.

2.9 Emergency Electric Motor Override

Provides procedures for emergency activation of the electric motor.

SECTION 3 - TROUBLESHOOTING AND FAULT CODES

3.1 Fault Codes

Lists and explains error codes displayed by the battery system components.

3.2 Battery System Troubleshooting (1 st & 2 nd Gen)

Guides on diagnosing and resolving issues with 1st and 2nd generation battery systems.

3.3 RamHino Diagnostic Tool

Explains the use of the RamHino tool for system diagnostics and data analysis.

3.4 Start Log

Describes how to start and use the logging function for system diagnostics.

JLG X390AJ-X14J Specifications

General IconGeneral
BrandJLG
ModelX390AJ-X14J
CategoryBoom Lifts
LanguageEnglish

Related product manuals