john deer Gator - User Manual

Questions and Answers

P
Phyllis MonroeAug 21, 2025
What to do if john deer Gator Control Module does not turn on?
- C
  Cynthia HolderAug 21, 2025
  If the Control Module or Display Module of your John Deer Spreader doesn't turn on, ensure all connections are fully seated. Remove the front wire harness and check for 12V at pins A-J at the rear connection attachment point. If there's no voltage, the wire harness may need replacement. Also, a faulty display can cause this issue, so consider replacing it. Ensure the vehicle has sufficient power or ground connection.
A
Aaron DiazSep 3, 2025
What to do for MD2 TLE OverTemp Fault on John Deer Spreader?
- R
  Robert LewisSep 3, 2025
  To address an MD2 TLE OverTemp Fault on your John Deer Spreader, reduce the module’s exposure to high temperatures to allow its internal temperature to fall below 75C. The module must then be power cycled to recover from the high temperature fault.
J
Jason SnyderSep 1, 2025
What to do for MD1 TLE OverTemp Fault on john deer Gator Spreader?
- A
  Alyssa OrtizSep 1, 2025
  To address an MD1 TLE OverTemp Fault on your John Deer Spreader, reduce the module’s exposure to high temperatures to allow its internal temperature to fall below 75C. The module must then be power cycled to recover from the high temperature fault.
P
pamchavezAug 31, 2025
What causes High Temperature Fault in john deer Gator?
- W
  William WilliamsAug 31, 2025
  A High Temperature Fault in your John Deer Spreader can be addressed by reducing the module’s exposure to high temperatures, allowing its internal temperature to fall below 75C. The module must then be power cycled to recover from the fault.
D
David WalkerAug 29, 2025
How to fix Lost Communication Fault on john deer Gator?
- M
  Michelle WillisAug 29, 2025
  To fix a Lost Communication Fault on your John Deer Spreader, make sure all wiring harness connections are secure and that all wiring is intact and undamaged. The modules must be power cycled to recover from the lost communication fault.
B
barry61Aug 27, 2025
What to do if john deer Gator Spreader shows MD2 Over Current?
- K
  Kimberly DominguezAug 27, 2025
  If your John Deer Spreader displays an MD2 Over Current fault, check the motor for damage. A heavily loaded or jammed actuator can also cause this, so reduce the load on the actuator or clear any jams before power cycling the module to recover from the over current fault.
B
braylindaAug 26, 2025
What to do if john deer Gator shows MD1 Over Current?
- W
  Wendy RiceAug 26, 2025
  If your John Deer Spreader shows an MD1 Over Current error, verify that the motor is not damaged. A heavily loaded or jammed spinner can cause this, so reduce the load or clear any jams before power cycling the module to recover from the over current fault.
D
Dawn EvansAug 25, 2025
Why is material not flowing from my John Deer Spreader when the gate is open?
- T
  tylermillerAug 25, 2025
  If material isn't flowing from your John Deer Spreader when the gate is open, check that the gate stop is in the correct position according to the calibration procedure, and adjust if necessary. Also, damp material may clump; always operate the spreader with the lid installed to prevent this.
D
Dustin BrownAug 23, 2025
How to fix no communication on John Deer Spreader?
- R
  Randy PorterAug 23, 2025
  To resolve a 'No Communications' issue on your John Deer Spreader, check for 12V at the Control Module pins M1-M4. Also, inspect the fuse on the Gator Harness, the chassis harness connection, and the spreader harness connection to ensure they are properly connected.

Summary

Introduction to Operators Manual

Using Your Operators Manual

Guidance on how to effectively use the operator's manual for safe operation.

Product Compatibility Information

Information on which vehicles the attachment is compatible with.

Safety Labels Explained

Safety Label Locations

Illustrates the placement of safety labels on the machine.

Understanding Machine Safety Labels

Explains the meaning of DANGER, WARNING, and CAUTION safety labels.

Multilingual Safety Resources

Information on obtaining manuals and labels in French or Spanish.

General Safety Precautions

Read Safety in Machine Operators Manual

Advised to read general safety precautions in the machine operator's manual.

Operating Safety Guidelines

Key safety points to follow during operation of the attachment.

Practice Safe Maintenance

Guidelines for performing maintenance safely and correctly.

Additional Safety Information

General Safety Practices

Guidelines for safe parking and appropriate attire during operation.

Chemical Handling and Disposal

Procedures for safely handling chemicals and disposing of waste products.

Assembly Instructions

Parts in Kit

Lists and illustrates the components included in the assembly kit.

Installation Guide

Spreader Assembly

Instructions for assembling the spreader unit itself.

Installing Spreader on Vehicle

Steps for attaching the assembled spreader to the vehicle.

Operation Overview

Vehicle Load and Tire Considerations

Guidelines for vehicle load capacity and tire inflation for safe operation.

Control Interface and Navigation

How to turn on and navigate the spreader's control display.

Spreader Components and Features

Overview of the spreader's parts and key operational features.

Spreader Operation Controls

Main Menu and Controls

Explanation of the main menu and default motor controls.

Settings Menu Options

Details on accessing and using the settings menu.

Operation Display Messages

Display Screen Messages

Explains potential error and status messages displayed on the screen.

Spreading and Adjustments

Spreading Procedure

Step-by-step guide for spreading material with the unit.

Adjusting Material Flow and Pattern

How to adjust flow rate, spread width, and barrier shield.

Spreader Calibration Procedures

Fertilizer Spreader Calibration

Instructions and considerations for calibrating the spreader for accurate distribution.

Calibration Requirements and Conversions

Details on necessary items, flow rates, and unit conversions for calibration.

Maintenance Recommendations

Routine Maintenance

Recommendations for keeping the spreader in good working order.

Removal and Storage

Removal Procedure

Steps for safely removing the spreader from the vehicle.

Storage Recommendations

Guidelines for properly storing the spreader.

Troubleshooting Common Issues

Display Module Error Codes

Lists and explains error codes related to the display module.

Troubleshooting Control Module Errors

Control Module Error Codes

Lists and explains error codes related to the control module.

Troubleshooting Motor Driver 1 Faults

MD1 Motor Driver Faults

Details on errors and troubleshooting for the MD1 (spinner) motor driver.

Troubleshooting Motor Driver 2 Faults

MD2 Motor Driver Faults

Details on errors and troubleshooting for the MD2 (gate actuator) motor driver.

Troubleshooting Communication and Version Errors

MD2 Communication and Version Errors

Troubleshooting for MD2 communication issues and version mismatches.

Wiring Diagram Details

Spreader Harness Connections

Pinout details for spreader harness connectors.

Control Module Output Terminals

Pinout details for the control module output terminals.

Product Specifications

Spreader and Motor Specifications

Details on hopper volume, capacity, motor type, speed, and draw.

Actuator, Dimensions, and Weight

Specifications for the electric actuator, overall dimensions, and empty weight.

Good Quality Service Information

John Deere Quality Service Process

Information on John Deere's quality service process and support.

Warranty Information

Limited Warranty Details

Outlines the terms and conditions of the limited warranty for licensed products.

john deer Gator Specifications

General

Brand	john deer
Model	Gator
Category	Spreader
Language	English