−17 −
27
27
27
27
28
28
28
28
28
28
29
No.
Item
Description
Setting
range
Ref.
page
52
53
54
55
56
57
Compensation of
solenoid-off
timing of reverse
feed stitching at
the start of
sewing
Compensation of
solenoid-off
timing of reverse
feed stitching at
the end of
sewing
Motor pulley
effective
diameter
Foot lift after
thread trimming
Bobbin thread
remaining
amount detection
function
Function of
bobbin thread
remaining
amount
detection
Compensation of releasing the solenoid for reverse feed stitching
when reverse feed stitching at the start of sewing is performed.
Compensation of releasing the solenoid for reverse feed stitching
when reverse feed stitching at the end of sewing is performed.
Effective diameter of pulley to be used for motor is set.
Function of lifting presser foot at the time of (after) thread trimming
0 : Not provided with the function of lifting presser foot after thread
trimming
1 : Provided with the function of lifting presser foot automatically
after thread trimming
Function of reverse revolution to lift the needle at the time of (after)
thread trimming
0 : Not provided with the function of reverse revolution to lift the
needle after thread trimming
1 : Provided with the function of reverse revolution to lift the needle
after thread trimming
Function of bobbin thread remaining amount detection device is set.
0 : Invalid
1 to : Valid function is selected.
–36 to 36
(10˚)
–36 to 36
(10˚)
50 to 140
5 (mm)
0/1
0/1
0 to
58
Function of
holding
predetermined
upper/lower
position of the
needle bar
Function of holding predetermined upper/lower position of the needle
bar
0 :Not provided with the function of holding predetermined upper/
lower position of the needle bar
1 : Provided with the function of holding predetermined upper/
lower position of the needle bar (holding force is weak.)
2 : Provided with the function of holding predetermined upper/
lower position of the needle bar (holding force is medium.)
3 : Provided with the function of holding predetermined upper/
lower position of the needle bar (holding force is strong.)
0 to 3
Indication of
function setting
53
18
52
16
55
1
56
0
58
0
Starting
position of
lowering
presser foot
Pedal stroke 2
for starting
thread trimming
Pedal stroke for
reaching the
maximum
number of
rotation
Compensation of
neutral point of
the pedal
Auto-lifter
selecting function
Holding time of
lifting auto-lifter
Pedal stroke 1
for starting
thread trimming
Pedal presser
lifting function
Compensation of
solenoid-on
timing of reverse
feed stitching at
the start of
sewing
Starting position of lowering presser foot
Stroke from the neutral position
Position 2 where the thread trimming starts from pedal neutral position
(When the function of lifting presser foot by pedal is provided.) (Pedal
stroke)
Position where the sewing machin reaches its highest sewing speed
from pedal neutral position (Pedal stroke)
Compensation value of the pedal sensor
Auto-lifter selection
0 : Solenoid drive system
1 : Pneumatic drive system
Limitation time of waiting for lifting solenoid type auto-lifter device
Position where thread trimming starts from pedal neutral position
(Standard pedal) (Pedal stroke)
PFL type of pedal type is set
0 : OFF
1 : ON
Compensation of starting the solenoid for reverse feed stitching when
reverse feed stitching at the start of sewing is performed.
8 to 50
(0.1 mm)
–60 to –10
(0.1 mm)
10 to 150
(0.1 mm)
–15 to 15
0/1
10 to 600
(second)
–60 to –10
(0.1 mm)
0/1
–36 to 36
(10˚)
42
43
44
45
46
47
48
50
51
*
*
*
44
150
43
–51
42
10
*
51
10
48
-35
46
0
45
0
*
47
60
*
50
0
54
500
57
0
* Do not change the set values with asterisk (*) mark as they are functions for maintenance. If the standard set value set at the time
of delivery is changed, it is in danger of causing the machine to be broken or the performance to be deteriorated.
(Descriptions of setting in this list are the standard values at the time of delivery.)
However, contents of function setting are subject to change for improvement of function and performance without notice.
41
–21
41
Starting
position of
lifting presser
foot by pedal
Position where the cloth presser starts lifting from pedal neutral
position (Pedal stroke)
–60 to –10
(0.1mm)
Start
level
U
U
U
U
U
S
U
U
S
U
U
U
S
U
U
S
U
(Start level ; U : User's mode, S : Service mode)
To Next Page
Loading...
Need help?
General
