āī18 ā
No.
Item
Description
Setting
range
29
29
29
30
33
33
33
33
33
33
34
34
34
34
Indication of
function setting
* Do not change the set values with asterisk (*) mark as they are functions for maintenance. If the standard set value set at the time
of delivery is changed, it is in danger of causing the machine to be broken or the performance to be deteriorated.
(Descriptions of setting in this list are the standard values at the time of delivery.)
However, contents of function setting are subject to change for improvement of function and performance without notice.
60
61
63
64
65
66
67
68
69
70
72
73
74
75
76
Function of stop
immediately after
reverse feed
stitching at the
start of sewing
Bobbin thread
remaining
amount detection
air blow output
time
Tie stitch
adjustment
function
Change-over
speed of EBT
(end back tack)
Selection of
thread trimmer
and additional
device function
Simplified
program setting
Auto hemmer
control
changeover
Prohibition of
start with
material end
sensor of auto
hemmer control
Selection of
speed control
method after
detection of
material end
sensor of auto
hemmer
control
Number of
stitches of
invalid material
end sensor of
auto hemmer
control
Clutch motor
function
Retry function
With/without
MF thread
trimming device
Rotating
direction of motor
One-shot
function up to
end of material
Presser lifter
solenoid initial
motion suction
time
Reverse feed
stitching at the
end of sewing
start time
Function at the time of completion of reverse feed stitching at the
start of sewing
0 : Not provided with the function of temporary stop of the sewing
machine at the time of completion of reverse feed stitching at
the start of sewing
1 : Provided with the function of temporary stop of the sewing
machine at the time of completion of reverse feed stitching at
the start of sewing.
Air blow output time when thread trimming with bobbin thread
remaining amount detection device is set.
Stop time of respective corners of start, end and overlapped stitching
is set.
Initial speed when starting reverse feed stitching at the sewing end
Selection of thread trimmer or additional device (UT or the like)
TrM : Thread trimming function
UT1 : Additional device 1
UT2 : Additional device 2
Setting of simplified program is performed.
Selection of auto hemmer control is performed.
0 : Control 1
1 : Control 2
Start of sewing machine is prohibited at the time of auto hemmer
control without cloth
0 : Invalid
1 : Prohibited
Speed after detection of material end sensor of auto hemmer control
is set.
0 : Depressing amount of pedal
1 : Set speed (motion at the set speed of No. 38)
Number of stitches which makes invalid material end sensor detection
with auto hemmer control is set.
Clutch motor control type is selected.
0 : OFF
1 : ON
This function is used when needle cannot pierce materials .
0 : Normal
1 :Retry function is provided.
This function sets with or without the MF thread trimming device
0 : Without
1 : With
Normal rotating direction of motor
0 : Clockwise
1 : Counterclockwise
One-shot automatic stitching up to end of material is performed. (Used
in case of without panel)
0 : Without one-shot function
1 : With one-shot function
Suction motion time of presser lifter solenoid
50 to 500 ms
Holding time of start speed of reverse feed stitching at the end of
sewing is set.
0/1
0 to 2000
(ms)
0 to 1000
(ms)
60
0
64
180
73
1
75
1
*
76
0
0 to 250
(rpm)
0/1
0/1
0/1
0 to 500
(0.5stitches)
0/1
0/1
0/1
0/1
0/1
50 to 500
(ms)
0 to 250
10 (ms)
61
500
65
Fun
66
Pro_
67
0
68
0
69
0
70
0
72
0
*
84
85
84
250
85
10
Ref.
page
59
1
29
59
Function of Auto/
Manual change-
over of reverse
feed stitching at
the start of
sewing
This function can specify the sewing speed of reverse feed stitching
at the start of sewing.
0 : The speed will depend on the manual operation by pedal, etc.
1 : The speed will depend on the specified reverse feed stitching
speed (No. 8).
0/1
63
10
74
1
Start
level
U
U
S
S
U
S
S
S
S
S
S
S
U
U
U
U
U
S
(Start level ; U : User's mode, S : Service mode)
To Next Page
Loading...
Need help?
General
