Juniper EX2200 Quick Start

EX2200 Switch Quick Start
To install and configure a Juniper Networks EX2200 Ethernet Switch, you need:
z Two mounting brackets and eight mounting screws (provided)
z A power cord with a plug appropriate for your geographical location and a power cord
retainer (provided)
z Ethernet cable with an RJ-45 connector attached (provided)
z Management host, such as a PC, with an Ethernet port (not provided)
z Screws to secure the chassis to the rack or cabinet (not provided)
z Phillips (+) screwdriver, number 2 (not provided)
For more information about the tasks described in this quick start and other setup tasks,
see the EX Series documentation at http://www.juniper.net/techpubs/.
Part 1: Mount the Switch
You can mount an EX2200 switch on two posts of a 19-in. rack or cabinet by using the
mounting brackets provided with the switch.
1. Place the rack or cabinet in its permanent location, allowing adequate clearance for
airflow and maintenance, and secure it to the building structure.
NOTE: If you are mounting multiple units on a rack, mount the heaviest unit at the bottom
and mount the other units from the bottom to the top in decreasing order of the weight of
the units.
2. Align the mounting brackets along the front or rear of the side panels of the chassis
depending on whether you are front-mounting or rear-mounting the switch.
3. Attach the mounting brackets to the chassis by using the mounting screws. Tighten
the screws.
NOTE: The switch weighs 10 lb (4.5 kg). Installing the switch requires one person to lift
the switch and a second person to secure it to the rack.
4. Have one person grasp both sides of the switch, lift the switch, and position it in the
rack, aligning the mounting bracket holes with the threaded holes in the rack rail.
Align the bottom hole in each mounting bracket with a hole in each rack rail, making
sure the chassis is level.
5. Have the second person secure the switch to the rack by using the appropriate
screws. Tighten the screws.
Part 2: Connect Power to the Switch
1. Squeeze the two sides of the power cord retainer clip and insert the L-shaped ends of
the wire clip into the holes in the bracket on each side of the AC appliance inlet on the
real panel.
2. Insert the coupler end of the power cord into the AC appliance inlet.
3. Push the cord into the slot in the adjustment nut of the power cord retainer. Turn the
nut until it is snug against the base of the coupler and the slot in the nut is turned 90°
from the top of the switch.
4. If the AC power source outlet has a power switch, set it to the OFF (0) position.
5. Insert the power cord plug into the power source outlet.
6. If the AC power source outlet has a power switch, set it to the ON (|) position.
g027019
S
Y
S
A
L
M
SPD
DX
EN
POE
g027020
Mounting rack
Mounting bracket
g027012
Tighten
adjustment nut.
Retainer clip
Adjustment nut

Juniper EX2200 Specifications

General

Throughput	77 Mpps
MAC address table	8000 entries
Jumbo frames support	Yes
Number of VLANs	1024
Networking standards	-
Switch type	Managed
SFP module slots quantity	4
Installed SFP modules quantity	0
Basic switching RJ-45 Ethernet ports quantity	48
Stackable	No
Product color	Black
Power consumption (typical)	100 W
Operating altitude	0 - 3048 m
Non-operating altitude	0 - 4877 m
Storage temperature (T-T)	-40 - 70 °C
Operating temperature (T-T)	0 - 45 °C
Storage relative humidity (H-H)	0 - 95 %
Operating relative humidity (H-H)	10 - 85 %

Weight and Dimensions

Depth	254 mm
Width	441 mm
Height	43 mm
Weight	3600 g