EasyManuals Logo

Juniper JUNOS 10.1 - RELEASE NOTES REV 4 User Manual

Juniper JUNOS 10.1 - RELEASE NOTES REV 4
205 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #65 background imageLoading...
Page #65 background image
The licenses are not synced between the master and backup Routing Engine
unless the system license traceoptions file file-name statement is configured.
[PR/501443]
Invalid XML characters such as &#x11 (0x11) or &#20 (0x14) are allowed to be
loaded into the router. As a result, the XML parsers break as the characters are
not XML compliant. [PR/502994]
The xnm service currently does not support logging of remote-host addresses in
system accounting. [PR/535534]
VPNs
When you modify the frame-relay-tcc statement at the [edit interfaces
interface-name unit logical-unit-number] hierarchy level of a Layer 2 VPN, the
connection for the second logical interface might not come up. As a workaround,
restart the chassis process (chassisd) or reboot the router. [PR/32763]
When you configure inter-AS VPLS with MAC processing at the autonomous
system (AS) boundary router along with multihoming, and if a designated
forwarding AS boundary router fails and then comes back up again, traffic flowing
to the local AS from the other ASs boundary router might be lost. The loss occurs
in the time period (tenths of a second) during which the old designated forwarding
AS boundary router is taking back the role of designated forwarder. [PR/312730]
On a router configured for nonstop active routing (NSR) (the nonstop-routing
statement is included at the [edit routing-options] hierarchy level), if a nonstop
active routing switchover occurs after the configuration for routing instances
changes in certain ways, the BGP sessions between PE and CE routers might not
be established after the switchover. [PR/399275]
On MX Series, M120, and new EIII FPCs on M320 routers, the ISO/Connectionless
Network Service (CLNS) packets over the translational cross-connect (TCC) are
dropped in the case of Frame Relay, even though the family TCC has been
configured to switch family iso on the Frame Relay interface. [PR/462052]
In vlan-tagging, stacked-vlan-tagging, and flexible-vlan-tagging modes, untagged
packets or mismatching Tag Protocol ID (TPID) packets may be dropped. These
dropped packets are not accounted for and are not visible in the CLI. This issue
is specific to the 10-port 10-Gigabit Oversubscribed Ethernet (OSE) PICs.
[PR/496190]
Under certain topologies, using NG-MVPN with the RPT-SPT mode can cause
traffic to be discarded from the RPT before the traffic starts flowing from the
SPT when the RPT is switched to SPT. [PR/529518]
If a VRF routing instance contains a static route that is resolved via a route that
was auto-exported from another routing instance, the static route may not be
removed when the physical interface goes down. [PR/531540]
When a CE-facing interface in a VPLS instance is deactivated, the routing protocol
process may get into a loop leading to a high CPU utilization. [PR/531987]
Issues in JUNOS Release 10.1 for M Series, MX Series, and T Series Routers 65
Issues in JUNOS Release 10.1 for M Series, MX Series, and T Series Routers

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Juniper JUNOS 10.1 - RELEASE NOTES REV 4 and is the answer not in the manual?

Juniper JUNOS 10.1 - RELEASE NOTES REV 4 Specifications

General IconGeneral
BrandJuniper
ModelJUNOS 10.1 - RELEASE NOTES REV 4
CategorySoftware
LanguageEnglish

Related product manuals