JVC CA-TD5 User Manual

02-1
34
order you have
Prepare CDs: (See page 21.)
Check that the CD Playér is not playing a CD.
* Set the source to CD.
Insert a cassette into the Tape Tray to record on.
When you want to record on both sides. of.a tape, press the REVERSE MODE button to tum Reverse
Mode on. Check that the recording direction for the tape and the Tape Direction indicator are correct.
(See page 33 “‘Notes.for.using Reverse Mode for recording”’.)
Press the CD REC START button.
“CD...; TAPE” appears. on. the display and the CD Player starts playing the first track to be recorded.
At the.end of the tape, the System automatically goes back to the beginning of the last selection and re-
records it, this time gently fading out at the end. If you selected the Reverse Mode, the reverse side starts
with the last selection on the first side and will be faded out at the end again. (About 10 second blank is
created at the beginning of the reverse side.) When. the recording is finished, the message “CD REC
FINISHED” scrolls by.on the display. The CD Player and Cassette Deck stop.
To Stop. at Any Time During the Recording Process.
Press the REC START/STOP or @ button.
The. recording. stops. when you press.the REC START/S1 Pe button. If you press the.@ button, the unit .
creates a. four second blank section. of, tape before, stopping.
Note: When making SLEEP timer settings while doing CD Direct recording, set the time so that there is
enough leeway to finish the recording before the power goes off. If the time is set to about the length of
the CD, the power may go off before recording finishes.
For CD Direct Recording using more than one disc, use a blank tape, If you use a prerecorded tape,
rded inaterial iriay not be erased between newly- ee aacks:
Auto
Edit
Recording
Using Auto. Edit, you can record the CD tracks to fit the tape, so a selection isn’t cut off. Auto Edit is one .
of the best ways to copy all of a CD onto a tape.
Auto Edit programs the CD tracks in numerical order. To prevent the end of the last track on the first side
from being cut off, the last track on.the first side.is selected to fit on the remaining tape length. 0.0... ..
Prepare the CD of CDs. (See page 21.)
Set the source to CD and check tha the CD Player is not playing a CD.
Press the MENU button.
The “TIMER” section of the menu display blinks.
the cursor key ta the right
or left (44 < or > p>) and select
“AUTO EDIT”.
‘The'display changes with each press of the
~~“ oursot keys as shown below. =
+ Press the left (<4 <) cursor key
++ TIMER <> CD P.MODE + REPEAT + AUTO EDIT «> SEA CONTROL +
Press the right (> »») cursor key >
* You cannot select AUTO EDIT if a source other than the CD Playéi is selected.
ENTER
ae
Press the cursor key up or down (A or v << ) and select the
disc.
The .display.changes with each press of the cursor
keys.as shown. below.
+ Press the up (»» A) cursor key
3 <> 2 <>
wn (V4) Cursor key >
* If you press the DISC (1-3) buttons instead of pressing the up or down (»™ A or VY <t )
: Keys, you.can. select the. disc. . :
EC--"a appears on the display, the
ago display shows.you the length of tape required to... -}-4
record the CD you selected.
NY size of the tape ar
“ea eleven ossibilities rogrammed | eee eats
80, 84, 90. Geieeci ee: to
select the length that matches the length of tape
‘you will be using, or the letigth nearest to the letigth you will be usiig:”
“oT you pick a tape'length shorter than’ the total playing timé of the CD, the last tracks on both
sides of the tape will be faded out as the tape ends.
Press the SET button.
“SIDE-B” blinks on the display and the tracks that
will be recorded.on side B of the tape are displayed.
, To Sidley the tracks that will be recorded on 7g ais
side A.of the tape, press the SET button again.
The. Unit switches between. side A.and.side B. with each press of the SET button... .
| Press the ENTER button.
When you want to record on both sides of a tape, press the REVERSE MODE button to tum Reverse
mode on.
yound, the Unit rewinds the
When the tape is ready, to prevent the start of a track being cut, the System creates a blank period of
about 10 seconds before it starts to record the CD. While a blank period is eated, “TAPE
SIDE-A STANDBY?” scrolls through the display. (The System aiso creates about 10 second blank
period at the. start of side B of the tape. While a blank period is being created, “TAPE SIDE-B
STANDBY?” scrolls through the display.)
When the recording is finished, the message “CD REC FINISHED” scrolls by on the display. The CD
Play p- |
To stop at any time while recording, press the REC START/STOP button or the. button. The _.
recording stops. when you. press the REC START/ STOP button. If you press the Ml button, the unit creates
To cancel Auto. Edit, press the: 4: butten on:the:-CD.Player or the ALL.CD EJECT. button: You'can:also
cancel Auto Edit by selecting play mode from the Unit or the Remote Control after stopping the recording.
Notes:
° Ifyou change any of the CD’s while using Auto. Edit, Auto Edit will be cancelled. Therefore, do not
change the.CD’s while using Auto Edit.
¢ When making SLEEP timer settings while: doing:Auto Edit recording, set the time. so that there is
enough leeway to finish the recording before. the power:goes off. If the. time is set to about the length
of the CD, the power may go off before recording finishes.
35
x
B
Bo
fe
Lil
YHSSOL-VO/SCL-VO

JVC CA-TD5 Specifications

General

Brand	JVC
Model	CA-TD5
Category	Speaker System
Language	English