JVC GR-SXM730U - Emergency Display; Demonstration Mode

1-14
E07 Short circuit of capstan MDA Power ON Power OFF
E06 CAPSTAN FG input absent EDIT Power OFF
E04 DRUM FF input absent DRUM rotation Power OFF
E03 SUPPLY REEL FG input absent REC, PLAY, SEARCH, FF
E02
Mode control motor rotates for more than 10
UNLOADING Power OFF
sec without shift to next mode.
E01
Mode control motor rotates for more than 10
LOADING Power OFF
sec without shift to next mode.
E00 Overtime the programming transaction REC, PLAY Power OFF
1.7 EMERGENCY DISPLAY
Whenever some abnormal signal is input to the
mechacon CPU, an error number (E01, as an exam-
ple) is displayed in the electronic view finder.
In every error status, such the message as shown be-
low alternately appear over and over.
E. VF/LCD Symptom Mode when observed Resulting mode
1.8 DEMONSTRATION MODE
This model has the DEMONSTRATION mode.
1) How to set the DEMONSTRATION mode.
The camera can be entered into the DEMONSTRA-
TION mode by setting on the DISPLAY screen appear-
ing in the viewfinder.
When entering the camera into the DEMONSTRATION
mode, pay heed to the following matters.
䊳
R
D
N
E
.
E
C
X
Z
T
M
O
S
O
O
Y
D
M
S
E
TEM ME
S
5
N
P
0
U
x
MENU Wheel
Recording Start/Stop Button
A
M
P
L
A
Y
O
F
F
䊳
F
E
M
T
O
X
.
O
C
P
W
U
O
.
S
S
S
B
C
Y
U
.
A
S
R
M
T
E
E
E
R
M
A
M
M
E
E
N
A
A
A
N
U
U
U
U
U
T
T
T
O
O
O
䊳
R
I
T
T
D
D
䊳
T
E
N
E
I
A
E
R
O
C
T
L
T
T
M
E
.
E
L
E
O
T
C
T
E
/
U
S
A
I
T
M
T
M
R
Y
M
M
I
A
L
I
O
N
S
E
E
M
C
A
M
D
T
R
E
R
N
E
E
E
A
O
G
M
.
M
M
E
E
N
O
O
O
F
O
N
U
F
F
F
R
F
U
F
F
F
E
F
NCH
1. Set the POWER switch to turn on
the "M".
Press the MENU WHEEL once. The
first page of the DISPLAY appears
on the LCD monitor (or in the
viewfinder).
2. Turn the MENU WHEEL in the
direction of the arrow to set the
cursor at “NEXT”.
Press the MENU WHEEL once.
The second page of the DISPLAY
appears on the LCD monitor (or in
the viewfinder).
Display 1
UNLOADING
[Power OFF
Display 2
Fig. 1-8-1
See to
next page
• In an emergency mode, all operations except
turning on/off the POWER switch are ineffectual.
No cassette is set in the camcorder or a cassette is set
in the camcorder but it is protected from recording.
Note 1) The indications of the DISPLAY page very
depending on the setting.
2) How to cancel the DEMONSTRATION mode.
To cancel the DEMONSTRATION mode, turn the
POWER switch off (“POWER OFF”).
E01
UNIT IN
SAFEGUARD MODE
E01
REMOVE AND
REATTACH BATTERY
Example (in case of the error number E01):