To Next PageTo Next PageWhy the connected Bluetooth audio player cannot be controlled on JVC KD-XD28BT?
If the connected Bluetooth audio player cannot be controlled on your JVC Car Stereo System: 1. Check whether the connected Bluetooth audio player supports Audio/Video Remote Control Profile (AVRCP). 2. Disconnect and connect the Bluetooth player again.
Why correct characters are not displayed on JVC KD-XD28BT Car Stereo System?
This JVC Car Stereo System unit can only display uppercase letters, numbers, and a limited number of symbols. Also, depending on the display language you have selected, some characters may not be displayed correctly.
What to do if “iPod ERROR” appears on JVC KD-XD28BT Car Stereo System?
If the message “iPod ERROR” appears on your JVC Car Stereo System, try the following: 1. Reconnect the iPod. 2. Reset the iPod. 3. Turn the power off and on again by pressing and holding B SRC for error recovery.
What to do if JVC Car Stereo System does not work at all?
If the JVC Car Stereo System does not work at all, reset the unit.
What to do if no Bluetooth device is detected on JVC KD-XD28BT?
If no Bluetooth device is detected by your JVC Car Stereo System: 1. Search from the Bluetooth device again. 2. Reset the unit.
What to do if “MISWIRING CHECK WIRING Turn the power off, then check to be sure the terminals of the speaker wires are insulated properly. Turn the power on again.” appears on my JVC KD-XD28BT Car Stereo System?
If you see “MISWIRING CHECK WIRING Turn the power off, then check to be sure the terminals of the speaker wires are insulated properly. Turn the power on again.”, turn the power off. Make sure that the terminals of the speaker wires are properly insulated, then turn the power back on.
What to do if “PROTECTING SEND SERVICE” appears on JVC KD-XD28BT Car Stereo System?
If the message “PROTECTING SEND SERVICE” appears, you should send the JVC Car Stereo System to the nearest service center.
What to do if “NO SIGNAL” appears on JVC KD-XD28BT Car Stereo System?
If your JVC Car Stereo System displays 'NO SIGNAL', ensure the antenna is mounted outside the vehicle.
What to do if “CHECK ANTENNA” appears on JVC KD-XD28BT Car Stereo System?
If your JVC Car Stereo System displays “CHECK ANTENNA”, check that the antenna and its connection are in good condition.
What to do if “CODE ERROR” appears on my JVC Car Stereo System?
If your JVC Car Stereo System displays 'CODE ERROR', ensure you've entered the correct pass code.
General| Bluetooth | Yes |
|---|---|
| Display Type | LCD |
| Dimensions | 7.21 x 2.09 x 6.22 inches |
| AUX Input | Yes |
| CD Player | No |
| Radio Tuner | AM/FM |
| Detachable Faceplate | Yes |
| Steering Wheel Control Ready | Yes |
| Android Music Playback | Yes |
| iPhone/iPod Music Playback | Yes |
| Display | LCD |
| Steering Wheel Control | Yes |
| Built-in Microphone | Yes |
| Power Output | 4 x 50W |
| Audio Formats Supported | MP3, WMA |
| Equalizer | 13-band |
| USB Port | Yes, Front |
| Preamp Outputs | 1 Pair (Rear/Subwoofer Selectable) |
| Pre-amp Outputs | 1 Pair (Rear/Subwoofer Selectable) |
Steps for initial setup, including crossover and clock settings.
Customizing sound with EQ settings, bass boost, and loudness.
Resolving issues related to sound, unit operation, and radio reception.
Addressing problems with USB/iPod connectivity.
Resolving SiriusXM and Bluetooth connectivity issues.
Understanding and recovering from device error messages.
Components for installation and step-by-step mounting instructions.
How to install the unit and connect wiring harness and components.
