JVC TM-1010PN - Input Select; Aspect Ratio

v-t
i
CONTROLS
AND
FEATURES
(cont'd)
<
Rear
Panel
>
“i
|
©)
©
000000000
:
Coote
:
o°o"0'0
0°"
OS
W
OB
oot'n
«
,
8
‘
ig?
0.0
5
o2
t
ei
0-0
ooo
1!
:
to
'
"
onwe
05050
Lo
7
a
NORMAL
For
TM-1010PN
FAST
20
(For European continent countries) .
To AC outlet TALLY! :
I
I ae (230 V AC, 50/60 Hz) oe
t
For TM-1010PN-K '
- CA; (For the United Kingdom)
[47|EXT SYNC terminals
External sync signal input (IN) and output (OUT)
[15] VIDEO A terminals
Video signal input (IN) and output (OUT) terminals.
The output terminal is bridge-connected. terminals. oe.
IN:
Video
signal
input
terminal
The
output
terminal
is
bridge-connected.
OUT
:
Bridge-connected
video
signal
output
terminal
IN:
Input
terminal
for
the
external
sync
signal
OUT : Bridge-connected output terminal
(Hote)
* Also refer to the Basic Connection Example on page 8.
[18] AUDIO A terminals
Input (IN) and output (OUT) terminals for the audio signal
corresponding to the VIDEO A terminals [15].
The output terminal is bridge-connected.
IN: Audio input terminal
OUT : Bridge-connected output terminal
* For corresponding video signals, use the VIDEO A
terminals [15].
[A9]AUDIO B terminals )
Input (IN) and output (OUT) terminals for the audio signal
* For corresponding audio signals, use the AUDIO A
terminals [18].
* Also refer to the Basic Connection Example on page 8.
[16] VIDEO B terminals
Video signal input (IN) and output (OUT) terminals for
both composite and Y/C-separated (S-Video) terminals.
Each output terminal is bridge-connected.
- [BNC terminals]
IN: Video signal input terminal
OUT : Bridge-connected video signal output terminal
[Y/C (mini-DIN 4-pin) terminals]
IN: Y/C-separated (S-Video) signal input terminal
OUT : Bridge-connected Y/C signal output terminal
corresponding to the VIDEO B terminals [16].
*
For
corresponding
audio
signals,
use
the
AUDIO
B
The
output
terminal
is
bridge-connected.
terminals
[19].
:
IN:
Audio
input
terminal
*
Y/C-
terminal
has
priority.
OUT
:
Bridge-connected
output
terminal
* Also refer to the Basic Connection Example on page 8. CN ote: )
inal pin layout
eyes
*
For
corresponding
video
signals,
use
the
VIDEO
B
terminals [16].
[20] AFC switch
Selects the AFC (Automatic Frequency Control) time
constant for the horizontal sync circuit.
Correct the skewed portion of the picture.
NORM position : Normal mode
FAST position : Fast mode (fast: smaller time constant)
[21] TALLY/REMOTE terminal
External control terminal (DIN 8-pin). Tally lamp, VIDEO
A/B (input selection), Under Scan, External Sync, 4:3/16:9
(aspect ratio), Pulse Cross, and Colour Off modes can be
controlled from an external unit.
* When you’re controlling the monitor externally via the
TALLY/REMOTE terminal, set all corresponding
switches on the front panel to the OFF (Mf) position.
(Whichever switch is pressed first has priority so remote
switches may not function if the panel switches are ON
(m) position.)
@ TALLY/REMOTE terminal pin layout
GND
COLOR OFF
{colour off)
ASPECT
RATIO
"| SELECT
| TALLYlamp SC ON/OFF lamp ON/OFF —
INPUT SELECT A/B
(VIDEO A/B)
UNDER SCAN ON/OFF
| Pin No. |
4 EXT SYNC ON/OFF
Ls (External Sync)
Ld
ASPECT RATIO 4:3/16:9
(4:3/16:9)
PULSE CROSS ON/OFF
COLOR OFF ON/OFF
(colour off)
[22| Power input connector
Supply power to either the AC IN or DC IN 12 V
connector.
[AC IN]
Connect the provided AC power cord between the AC IN
connector and an AC outlet (230 V AC, 50/60 Hz).
[DC IN 12V}
Connect the 12 V DC power plug to the DC IN 12V
connector.
* AC IN connector can function between 100 and 230 V
AC, 50/60 Hz.
* See your dealer for more information on 12 V DC power
supply.
* When both AC IN and DC IN connectors are used, the
AC input has priority.
* The DC power supply does not automatically take over
if an AC outlet is unplugged or the AC power is cut off
when both AC and DC power supplies are connected. In
this case, press the POWER switch to set to OFF, then
press it again to turn the power ON.
M@ DC IN 12V connector pin layout
DC IN
12V 3
1
[23] Power cord
Connect the provided power cord (230 V AC, 50/60 Hz) to
the AC IN connector. :
* The TM-1010PN power cord is for use in European
continent countries.
“The TM-1010PN-K power cord is for use in the United
Kingdom only. (The power cord for the United Kingdom
has a fuse built into the plug to the AC outlet.)
[24]External battery mounting holes
Attach an external battery to either pair of holes (1 or 2) to
use 12 V DC power (depending on the type of battery).
* External batteries manufactured by PAG or Anton Bauer
are available.
*See your dealer for details.
[25] Switch/control adjustment holes for service
personnel
For adjustment of SET UP switch, CUT OFF (B, R, G)
control and DRIVE (R, G) control during servicing.
* These controls are exclusively for the use of service
personnel. Do not attempt to adjust them.yourself.
ENGLISH