CONNECTING GAS DRYERS
GAS REQUIREMENTS (GAS MODELS ONLY)
A WARNING: To reduce the risk of fire,
electric shock, or injury to persons when using this
appliance, follow basic precautions, including
the following:
* Gas supply requirements: As shipped from the
factory, this dryer is configured for use with natural
gas (NG). It can be converted for use wlfh propane
(LP) gas. Gas pressure must not exceed 8 inches
wafer column for (NG), or 13 inches wafer column for
(LP).
* A qualified service or gas company technician must
connect tee dryer to the gas service. Failure to follow
these instructions can result in fire, explosion, or death.
* isolate the dryer from the gas supply system by
closing its individual manual shutoff valve during any
pressure testing of the gas supply. Failure to do so can
result in fire, explosion, or death.
* Supply llne requirements: Your laundry room must
have a rigid gas supply llne to your dryer. In the
United States, an individual manual shutoff valve
MUST be installed within at least 6 ft. (1.8 m) of the
dryer, in accordance wlth the Naflonal Fuel Gas Code
ANSI Z223.1 or Canadian gas installation code CSA
B149.1. A % inch NPT pipe plug must be installed.
Failure to do so can result in fire, explosion, or death.
* If using a rigid pipe, the rigid pipe should be 1½ inch
IPS. if acceptable under local codes and ordinances
and when acceptable to your gas supplier, ¾ inch
approved tubing may be used where lengths are less
than 20 ft. (6.1 m). Larger tubing should be used for
lengths in excess of 20 ft. (6.1 m). Failure to do so can
result in fire, explosion, or death.
* Connect the dryer to the type of gas shown on
the nameplate. Failure to do so can result in fire,
explosion, or death.
* To prevent contamination of the gas valve, purge the
gas supply of air and sediment before connecting
the gas supply to the dryer. Before tightening the
connection between the gas supply and the dryer,
purge remaining air until the odor of gas is detected.
Failure to do so can result in fire, explosion, or death.
* DO NOT use an open flame to inspect for gas leaks.
Use a noncorrosive leak detection fluid. Failure to do
so can result in fire, explosion, or death.
* Use only a new AGA- or CSA-certified gas supply
llne with flexible stainless steel connectors. Failure to
do so can result in fire, explosion, or death.
* Securely tighten all gas connections. Failure to do so
can result in fire, explosion, or death.
* Use Teflon tape or a pipe-joint compound that is
insoluble in propane (LP) gas on all pipe threads.
Failure to do so can result in fire, explosion,
or death.
* DO NOT attempt any disassembly of the dryer;
disassembly requires the attention and tools of
an authorized and qualified service technician or
company. Failure to follow this warning can result in fire,
explosion, or death.
ELECTRICAL REQUIREMENTS FOR
GAS MODELS ONLY
* Do not, under any circumstances, cut or remove the
third (ground) prong from the power cord. Failure
to follow this warning can result in fire, explosion, or
death.
* For personal safety, this dryer must be properly
grounded. Failure to follow this warning can result in
fire, explosion, or death.
* The power cord of fhls dryer is equipped with
a 3-prong (grounding) plug which mates with a
standard 3-prong (grounding) waft outlet to minimize
the posslbiffty of electric shock hazard from this
appffance. Failure to follow this warning can result in
fire, explosion, or death.
* This dryer must be plugged into a 120-VAC, 60-Hz.
grounded outlet protected by a 15-ampere fuse or
circuff breaker. Failure to follow this warning can result
in fire, explosion, or death.
* Where a standard 2-prong waft outlet is encountered,
it is your personal responslbifffy and obffgafion to
have it replaced with a properly grounded 3-prong
wall outlet. Failure to follow this warning can result in
fire, explosion, or death.
3-prong
grounding
type watt
grounding
plug
Ensure proper
ground exists
before use.
10
To Next Page
Loading...
