KENT C-4 - Brush Assembly C4;C4-A

Part # Qty Notes
10001 1 ea
10002 1 ea
10004 2 ea
10005 2 ea
10008 2 ea
10009 1 ea
10011 1 ea
10016 1 ea
10018 4 ea
10025 1 ea
10031 1 ea
10038 1 ea
10040 1 ea
10042 2 ea
10057 5 ea
10150 1 ea
10152 1 ea
10158 2 ea
10164 2 ea
10174 6 ea
10188 1 ea
10190 4 ea
10250 2 ea
10251 1 ea
10256 1 ea
10077 1 ea
10255 1 ea
10274 3 ea
10275 4 ea
18005 1 ea
NFS 1 ea
10104 2 ea
10131 1 ea
10199 1 ea
18008 3 ea
10107 1 ea
10131 1 ea
18010 2 ea
18018 1 ea
1 ea
10010 1 ea
10012 1 ea
1 ea
10183 2 ea
10174 2 ea
10182 2 ea
2 ea
10014 1 ea
10017 1 ea
10195 1 ea
Washer, Lock #10 SS
Washer, Brush Core
Shaft, Brush
Pulley, Set Screw-Shaft
Brush Assembly C4 / C4-A
Housing, Brush/Alum. Casting
Clip, Nozzle-Rear
Bolt, 6-32 x 1/4 Phil SS
Description
Tag, Wire B/Brush Motor (C4)
Brass, Elbow 90 D
Wire, Ground Housing Brush Assembly
Terminal, Ring #10
Terminal, Bullet Female-Ground
Washer, Flat #8 SS
Washer, Lock #10 SS
Clamp, 1/4 Sol. Hose-SS
Bolt, 10-24 x 1/2 Hex SS
Cuff, Hose-Female, Black
Hose, Vac Nozzle to Disconnect 1 1/4 I.D. x 21
Hose, Solution-90D Elbow to T - 1/4 I.D. x 2 3/8
Hose, Solution-Plug to T - 1/4 I.D. x 21
Clamp, 1/4 Sol. Hose-Zinc
Bumper, Assembly
Brush Core Sub-Assembly
Hose, Vac Nozzle to Disconnect with Cuff
Bolt, 8-32 x 5/16 Phil SS
Washer, Flat #10 SS
Motor, Brush C-4 115 Volt, Unwired
Terminal, Spade-Male
Terminal, Ring #10
Motor-Brush Wired C4 115 Volt Assembly
Bolt, 10-24 x 1/2 Phil SS
Bolt, 10-32 x 3/8 Hex Ground, Grn
Wire, Tie-6"
Bracket, Brush
Rivet, Alum 5/32 x 1/4
Gasket, 2 Part-Brush/Sw. Panel
Clip, Nozzle-Front
Brass, Plug 1/4 Barb
Brass, T-1/4 x 1/4 x 1/4 Barb
Spray Tip 11007 1/8 Mnpt-Got.
Washer, Lock #6 SS
Strap, Motor Brush
Pulley, Threaded-Motor
Belt, Gear
Bolt, 10-24 x 3/4 Hex SS
Brush, Reel With Flange
Bearing Block Assembly
18016
Bearing, Cap (metal)
Bearing, Ball SS
Bearing, Block (clear rubber)
10013
18210
17