Kinoton FP 30 D - Plans of Terminal Connections; Relay Control Board 8134-3

105 pages

Save Page as PDF

To Next Page

To Previous Page



Issue: 04/2011



 

 

Terminal Connections

Main Page

Table of Contents5
Safety11
Safety Notes11
General Hints11
Dangers When Working with the Projector11
Intended Purpose12
Guarantee and Liability12
Explanations of Symbols and Notes13
Special Hazard Points14
Electric Power Hazards14
Lamphouse Hazards15
Broken Glass15
UV Radiation15
High Voltage15
Mechanical Danger15
Preventing Projector Damage16
Service16
Protective Devices17
Main Switch17
IR Reflex Film Break Sensor17
Film Stripper17
Lamphouse Door Switch18
Lamphouse Airflow Switch18
Transportation and Installation / Mounting19
Transportation19
Delivery or Equipment Variations19
Installation20
Place of Installation, Place of Operation20
Important Hints for Installation21
Mounting22
Filling with Oil22
Installation Hints22
Installing and Connecting the Lamphouse Components23
Connecting the Water Cooling (Option)24
Connecting the Projector24
Connecting the Non-Rewind System to the Projector24
Function and Components25
Components Overview25
Projection Drive25
Console25
Xenon Unit25
FP 50 D Variations26
Projector Head28
Film Gate and Film Track29
Film Pressure Skate29
The Dowser30
Single Aperture Plates (Only with Manual Lens Turret or Lens Holder)31
Aperture Changer (Option, Only with Electronic Lens Turret)31
Drive and Control32
Format Change with Three Lenses32
Format Change with Two Lenses Turret32
Changing the Format Combination33
Lens Holder33
Lens Turret (Option)34
Manual Lens Change34
Electronically Controlled Lens Change (Option)35
Focusing36
Manual Focusing with Lens Turret / Lens Holder36
Electronic Focusing with Lens Turret (Option)36
Electronically Controlled Lens Holder Focusing (Option)36
Rotating Shutter37
Intermittent Sprocket38
Framing38
Constant Speed Sprockets39
Reverse-Scan Sound Device40
Analog Reverse-Scan Sound Device (Non-Upgradeable)40
Reverse-Scan Sound Device Analog and Optional DOLBY Digital (Upgradeable)41
Components41
Sound Tracks on the Films42
SDDS Reader / DTS Reader (Option)42
Film Cleaner (Option)42
Film Transport Systems43
Friction Shafts with Film Spools43
Guide Roller Set for Operation with a Platter System (Option)44
Friction Shafts and Guide Rollers44
Drive Components in the Projector Head45
Main Drive46
Intermittent Movement (also Called a Maltese Cross or a Geneva Movement)46
Electronic Components47
Automation Systems48
Rectifiers49
Xenon Sensor (Option)49
Lamphouse Components50
Xenon Unit51
Xenon Bulb51
Mirror52
Operating Elements53
Projector Console53
Main Switch53
Projector Operating Panel53
Auditorium Remote Operating Panel (Option)54
Projector Lamphouse55
Ammeter55
Operating Hour Counter55
Fuse55
Main Switch55
Ignition Button56
Rectifier56
Operation and Troubleshooting57
Switching on and Starting the Projector57
Stopping and Switching off Projector57
Threading for Projection Operation58
General Threading58
Threading from a Non-Rewind / Platter System59
Troubleshooting60
General Hints60
Projector Troubleshooting Chart (Type 1 Errors)60
Projector Troubleshooting Chart (Type 2 Errors)60
Analog Sound62
Digital Sound62
Lamphouse Troubleshooting Chart63
Cleaning / Maintenance / Repair65
General Hints65
Cleaning65
Maintenance67
Drain and Refill Oil (Kinoton Type 3672 Oil)68
Changing the Intermittent Oil68
Repair and Adjustments68
Changing the Pilot Lamp68
Adjusting the Film Pressure Skate69
Adjusting the Height of the Film Pressure Skate70
Changing the 35 MM Film Runner Strips71
Adjusting the Lens Holder72
Changing a Constant Speed Sprocket / Pad Shoe72
Adjusting the Tension of the Pad Shoe Spring73
Adjusting the Distance between Pad Shoe and Sprocket73
Adjusting the IR Reflex Film Break Sensor73
Tension the Chains74
Adjusting the Mechanical Friction75
Changing and Lubricating the Felt Disk of the Mechanical Friction76
Adjusting the Tension of the Friction Toothed Belt76
Changing the Xenon Bulb77
Adjusting the Illumination of Screen80
Adjusting the Intensity of Currents81
Checking the Light Arc Stabilizing Magnet81
Changing the Reflector82
Changing the Heat Filter85
Parts and Wearing Parts87
Film Gate Parts87
Feed/Bottom Sprocket Parts87
Guide Roller Parts87
Other Parts87
Parts for Drive and Motors88
Film Spools88
Friction Shafts and Interchangeable Flanges with Shafts88
Electronic and Control Parts88
MM Apertures for Aperture Changer93
Single Apertures93
Adapter Rings for 35 MM Lenses94
Xenon Bulbs and Adapters94
Technical Data, Circuit Diagrams and Plans of Terminal Connections95
Technical Data95
Projector95
Reverse-Scan Sound Device96
Plans of Terminal Connections97
Relay Control Board 8134-397
Basic Unit Overview98
Main Terminal Strip (Optional with Terminal 25 - 50)99
Terminal Strip with CCA3, DMP1 or SA2100
Circuit Diagrams101
400 V 3-Ph Mains Connection101
240 V Mains 3-Ph Connection (USA)102
240 V Mains 3-Ph Connection (Japan)103
Lamphouse104

Kinoton FP 30 D - Plans of Terminal Connections; Relay Control Board 8134-3

Table of Contents

Related product manuals