Kodiak 40” User Manual

PLEASE LOOK AT THE COVER FOR ANY MARKING,
SO THE CORRECT COVER WILL BE SENT TO YOU.
40”, 4’, AND 5’ STANDARD 3 POINT HITCH CUTTER PTO COVER
PART NUMBER CPC-5
6’ STANDARD 3 POINT HITCH CUTTER PTO COVER
PART NUMBER CPC-6
7’ SERIES 6 PTO COVER
PART NUMBER K-39589
FOR HEAVY DUTY PTO SERIES 5 PTO COVER
PART NUMBER IS CPCHD-5
STANDARD 3 POINT HITCH PTO
40” SERIES #4 PART NUMBER 109-40
4’ SERIES #4 PART NUMBER 111-60
5’ SERIES #4 PART NUMBER 111-60
6’ SERIES #4 PART NUMBER 112-72
SLIP CUTCH STANDARD PTO
6” SERIES #4 PART NUMBER 113-72SC
MEDIUM DUTY 3 POINT HITCH PTO
5’ SERIES #4 PART NUMBER 111-60
6’ SERIES #4 PART NUMBER 112-72
SLIP CLUTCH MEDIUM DUTY
5’ SERIES #4 PART NUMBER 113-72SC
6’ SERIES #4 PART NUMBER 113-72SC
HEAVY DUTY 3 POINT PTO
5’ SERIES #5 PART NUMBER 111-60SC
6’ SERIES #5 PART NUMBER 113-72H
7’ SERIES #6 PART NUMBER 113-84H
8’ SERIES #5 PART NUMBER 111-60SC
10’ SERIES #5 PART NUMBER 111-60SC
PULL TYPE
40” SERIES #4 PART NUMBER 111-60
4’ SERIES #4 PART NUMBER 111-60
5’ SERIES #4 PART NUMBER 112-72
6’ SERIES #4 PART NUMBER 113-72 H-P
MEDIUM DUTY PULL
5’ SERIES #4 PART NUMBER 112-72
5’ SERIES #4 PART NUMBER 113-72SC
6’ SERIES #4 PART NUMBER 113-72
HEAVY DUTY PULL
6’ SERIES #5 PART NUMBER 113-72 H
7’ SERIES #6 PART NUMBER 113-84 H
LONG CONE USED
ONLY ON
SHEAR PIN/
SP LINED YOKES
(TRACTOR OR
IMPLEMENT END).
PTO SHAFT COVERS
24
10/11
***NOTE: SHIELDS ARE FOR UP TO 910MM AND 1210MM X-X DRIVE LINES...CUT TUBES TO FIT
ASSEMBLE THE SHIELDS ON EACH HALF, THEN CUT THE TUBES THE SAME LENGTH AS THE
SLIP TUBES. MAKE SURE THEY DO NOT COME TOGETHER AND BIND WHEN THE 2 HALVES
ARE ASSEMBLED.
ALWAYS KEEP SHIELDING IN PROPER WORKING ORDER, USE PROPER LENGTH CONES, AND
MAKE CERTAIN ALL SHIELDING FURNISHED WITH EQUIPMENT OR DRIVE LINE IS IN PLACE
AND THAT THE CROSSES AND YOKES ARE COMPLETELY COVERED BY EITHER THE INSTALLED
SHIELD OR EQUIPMENT. IT IS THE USER’S RESPONSIBILITY TO USE CORRECT SHIELDING.
Complete PTO’s
K-36725 [90SL4069] 910mm:
Complete Shield Series 4 – 40” and 48” STD Cutter
K-36728 [90SL4099] 1210mm:
Complete Shield Series 4 – 60” and 72” STD Cutter
ADD TO ABOVE K-4114 SHORT CONE: Add price for complete shaft.
Shield with 1 STD Cone / 1 short cone - for slip clutch driveline.
ADD TO ABOVE K-4115 LONG CONE: Add price for complete shaft.
Shield with 2 long cones - for splined yoke both ends.

Kodiak 40” Specifications

General

Brand	Kodiak
Model	40”
Category	Lawn Mower
Language	English