To Next Page
M
Morgan TaylorSep 7, 2025
What to do if Kohler 50EOZ controller master switch is in OFF/RESET position?
- JJohn GarrisonSep 7, 2025
If the controller master switch is in the OFF/RESET position, move it to the RUN or AUTO position.
What to do if Kohler 50EOZ controller master switch is in OFF/RESET position?
If the controller master switch is in the OFF/RESET position, move it to the RUN or AUTO position.
What to do if Kohler 50EOZ Marine Equipment fuel tank is empty?
If the fuel tank is empty or the fuel valve is shut off, add fuel and move the fuel valve to the ON position.
What to do if Kohler Marine Equipment controller fuse blown?
If the controller fuse is blown, replace it. If the fuse blows again, troubleshoot the controller.
What to do if Kohler 50EOZ Marine Equipment oil level low?
If the oil level is low, restore it and inspect the generator set for oil leaks.
What to do if AC output circuit breaker open in Kohler 50EOZ?
If the AC output circuit breaker is open, reset the breaker and check for AC voltage at the generator side of the circuit breaker.
How to clean seawater strainer in Kohler 50EOZ Marine Equipment?
To resolve a clogged or restricted seawater strainer, clean the strainer.
What to do if Kohler Marine Equipment controller master or start/stop switch inoperative?
If the controller master or start/stop switch is inoperative, replace it.
What to do if Kohler Marine Equipment has exhaust system leak?
If there is an exhaust system leak, inspect the exhaust system and tighten the loose exhaust system components.
How to reset fault switches on Kohler Marine Equipment?
If there is a fault shutdown, reset the fault switches and troubleshoot the controller.
How to bleed air from fuel system in Kohler 50EOZ (diesel only)?
If there is air in the fuel system (diesel only), bleed the diesel fuel system.
General| Model | 50EOZ |
|---|---|
| Power Output | 50 kW |
| Cooling System | Heat exchanger |
| AC Voltage | 120/240V |
| Hertz | 60 Hz |
| Fuel Type | Diesel |
| Starting Type | Electric |
| Engine Type | Diesel |
| Phase | Single or Three-phase |
Regional contact information for Kohler Power Systems in China.
Regional contact information for Kohler Power Systems in Africa, Europe, and Middle East.
Regional contact information for Kohler Power Systems in the Asia Pacific region.
Regional contact information for Kohler Power Systems in Japan and Korea.
Regional contact information for Kohler Power Systems in Latin America.
Identifies maintenance and service parts for the generator set.
Identifies related literature available for the generator sets.
Provides information on generator set and engine specifications.
Details the alternator, excitation system, and voltage regulator.
Illustrates and labels key components of the generator set.
Describes a kit for monitoring the generator set from a remote location.
Senses output current and shuts off AC voltage regulator on overload.
Interrupts generator output on overload or short circuit.
Includes contacts that energize during generator operation to control devices.
Lists checks and inspections to perform before or at each startup.
Recommends vessel inspection, especially the exhaust system, by Coast Guard Auxiliary.
Details angular operation limits for units covered in the manual.
Addresses specific regulations for operation in EU countries regarding noise emissions.
Procedures for operating the generator set under load weekly for one hour.
Explains the operation of the Decision-Maker 3+ controller and its modes.
Describes the controls and indicators on the controller.
Details fuses and terminal strips on the controller circuit board.
Defines possible auxiliary fault lamp conditions and their causes.
Provides procedures for starting the generator set locally or automatically.
Outlines procedures for normal and emergency stopping of the generator set.
Explains how to enable, disable, start, and stop in prime power mode.
Lists fault conditions that cause automatic shutdown and restart requirements.
Details the procedure to restart the generator after a fault shutdown.
Outlines the procedure to restart the generator after an emergency stop.
Explains the controls and functions of the expanded controller.
Describes the controls and indicators located on the expanded controller.
Procedures for starting the generator set locally or automatically.
Outlines the procedure for normal stopping of the generator set.
Lists fault conditions that cause automatic shutdown and restart requirements.
Explains the controls and functions of the standard controller.
Describes the controls and indicators located on the standard controller.
Procedures for starting the generator set locally or automatically.
Outlines the procedure for normal stopping of the generator set.
Lists fault conditions that cause automatic shutdown and restart requirements.
Details the procedure to restart the generator after a fault shutdown.
Provides general maintenance safety precautions and guidelines.
Lists recommended maintenance intervals for cooling, exhaust, engine, and generator systems.
Covers checking coolant levels and system warnings.
Details the procedure for inspecting the siphon break.
Outlines the steps for inspecting and replacing the seawater pump impeller.
Details exhaust system inspection points and carbon monoxide warnings.
Provides procedures for storing the generator set for extended periods.
Details preparing the lubricating system for storage.
Details preparing the cooling system for storage.
Details preparing the fuel system for storage.
Details preparing the exterior for storage.
Details battery storage procedures.
