Why does my Kohler Marine Equipment emit black or gray smoke?
If your Kohler Marine Equipment generator emits black or gray smoke, check the oil level. Also check compression, as the issue might be worn piston rings or valves.
What to do if Kohler Inverter experiences a fault shutdown?
If your Kohler Inverter experiences a fault shutdown, reset the controller.
How to troubleshoot erratic operation of my Kohler Marine Equipment?
If your Kohler Marine Equipment operates erratically, adjust the governor stability. Clean the cylinder head to address potential carbon buildup in the engine. Check cylinder pressures with a leakdown test and inspect the valves and valve seats to ensure the engine valves are seating correctly.
What to do if my Kohler 5EFKOD overheats?
If your Kohler Marine Equipment overheats, inspect the cooling system for air intake obstructions. Also, check the engine coolant system for blockages and clean as necessary to ensure adequate cooling.
How to fix a Kohler Marine Equipment generator that starts hard?
If your Kohler Marine Equipment generator starts hard, check the battery voltage, power supply, and operation to address potential low battery voltage. Inspect the compression to identify worn piston rings or valves. Also, verify that battery voltage is present at each glow plug (control wire to ground) while cranking. To check glow plug condition, remove each glow plug and measure the resistance from the control wire connection point to the tip of the glow plug; a resistance of approximately 1 ohm indicates a good glow plug.
Why does my Kohler Marine Equipment generator lacks power?
If your Kohler Marine Equipment generator lacks power, inspect air intakes and the exhaust for obstructions to ensure adequate cooling. Check the controller configuration setting and adjust the governor speed to ensure the engine is running at its rated RPM. Test and readjust the governor if there is a malfunction or misadjustment.
What to do if my Kohler 5EFKOD Marine Equipment starts but shuts down?
If your Kohler Marine Equipment generator starts but shuts down, check the controller’s display for a fault shutdown code. Correct the fault and then reset the controller.
Why my Kohler Marine Equipment cranks but does not start?
If your Kohler Marine Equipment generator cranks but does not start, begin by checking the fuel supply and fuel filters for any blockages. Inspect for loose or open connections at the fuel pump or fuel solenoid, and check the controller/engine wiring continuity. Ensure that the controller configuration settings are correct. Also, check for a locked rotor, which may be indicated by an overcrank fault shutdown.
What to do if my Kohler Marine Equipment generator set does not crank?
If your Kohler Marine Equipment generator set does not crank, there are several potential causes. It could be due to a weak or dead battery, in which case you should recharge or replace the battery. Check for reversed or poor battery connections. Inspect for loose connections or open circuits in the engine/controller connections, and verify the wire harness continuity. Replace the F2 fuse if it's blown; if it blows again, inspect the circuit and components, controller wiring, starter solenoid, and wiring for open grounds, loose connections, or pushed-out pins. Check the crank relay for 12VDC on lead 71N. Clean and retighten any poor ground connections. Inspect the starter and controller connections and operation, ensuring power to the controller.
What to do if Kohler Inverter shows low oil pressure shutdown?
If your Kohler Inverter experiences a low oil pressure shutdown, replace the low oil pressure switch. Also, check the engine for any potential damage.
General| Brand | Kohler |
|---|---|
| Model | 5EFKOD |
| Category | Marine Equipment |
| Language | English |
Record for identifying the generator set model and serial number for service.
Record for identifying the engine model and serial number for service.
Critical safety procedures to prevent accidental generator set startup during maintenance.
Warnings about flammable fuels, sparks, and fire risks during operation and maintenance.
Safety information regarding the exhaust system, emphasizing carbon monoxide risks.
Detailed information on the dangers and symptoms of carbon monoxide exposure from exhaust gases.
Precautions for safely handling, storing, and using fuels to prevent leaks and explosions.
Warning about potential hearing loss from generator set noise and the need for a muffler.
Critical safety warnings about electrical shock and injury from moving components and wiring.
Warnings about short circuits, backfeed, and testing live electrical circuits to prevent injury.
Safety advice concerning hot components like coolant and steam, and precautions before servicing.
Notices regarding fuse replacement, saltwater damage, and general maintenance safety.
List of recommended parts for maintenance and service of the generator set.
References to other manuals and documentation for generator set installation, operation, and service.
Illustrated diagrams showing the typical components and service points of the generator set.
Essential checks to perform before starting the generator set for safe and satisfactory operation.
Recommendations for boat inspections, angular limits, EU operation, and load profile guidelines.
Detailed guide on operating the generator set using the Advanced Digital Control interface and its features.
Information on controller settings, time delays for faults, and warning specifications for generator set operation.
Summary of available menu displays for monitoring generator set data and settings.
Procedures for accessing and setting up controller data via the digital display or a personal computer.
Guide to navigating and understanding various data points and adjustments available through the controller menus.
Basic maintenance tasks, safety precautions, and general service guidelines for the generator set.
Detailed schedule of maintenance tasks and their required intervals for specific generator set models.
Procedures and specifications for checking and changing engine oil and oil filters.
Guidelines for fuel specifications, replacing the fuel filter, and bleeding the fuel system.
Instructions for inspecting and maintaining the exhaust system to ensure safety and performance.
Procedures for checking, filling, flushing, and cleaning the engine cooling system and its components.
Instructions for checking and adjusting the seawater pump belt tension for proper operation.
Guidelines for battery care, maintenance, and proper procedures for storing the generator set.
Information on fault codes displayed by the controller and diagnostic procedures for identifying issues.
Tables listing common trouble symptoms, probable causes, and recommended actions for diagnosing and fixing problems.
A guide to referencing point-to-point and schematic wiring diagrams for different generator set models.
Schematic and point-to-point wiring diagrams for generator sets without an isolated ground configuration.
Schematic and point-to-point wiring diagrams for generator sets with an isolated ground configuration.
To Next Page
