Kold-Draft GB1064AC - User Manual

- -
Installation, Operation, Technical
Service and Replacement Parts Manual
Ice Cube Makers - GT36x, GT56x, GB56x, GB106x
Stacking Instructions - Multiple GB56x or GB106x
Ice Cube Crushers - T27x
Pre-charged Remote Air-Cooled Condenser - RC214APV
GT36x GT56x GB56x GB106x
KDIndustries, Inc.
1525 East Lake Road
Erie, PA 16511-1088 U.S.A.
(800) 840-9577
FAX: (800) 548-9392
www.kold-draft.com
November 2016
This manual is updated periodically. Visit http://www.kold-draft.com/resources/literature.php for the latest version.

Summary

ICE CUBER-SAFETY INFORMATION

ICE MAKER IDENTIFICATION

ICE CUBER INSTALLATION

Installation Warnings

General installation warnings and safety precautions for the ice cuber.

Pre-Install Checklist

ASSEMBLY

Assembly Procedure

Step-by-step guide for assembling the ice machine.

INITIAL START PROCEDURE

ICE MACHINE CLEANING PROCEDURE

SPECIFICATIONS

COMPONENTS

Mechanical Components

Controller

Fault Codes

Lists conditions that shut down the machine to prevent damage.

ERROR-CODE TROUBLESHOOTING

Fault Code 10: Evaporator temp over 120 F

Indicates evaporator temperature is too high.

Fault Code 20: Water Plate failed to close...

Water plate failed to close after three attempts.

Fault Code 30: Freeze time exceeds 60 min.

Freeze cycle time is too long.

Fault Code 40: Freeze time less than 5 min., for 3 consecutive times.

Short freeze cycles detected three times.

Fault Code 50: Harvest cycle exceeds 20 min.

Harvest cycle duration is too long.

Fault Code 60: Water fill exceeds 5 min.

Fault Code 70: Evaporator Temperature < 31 F, during water fill only.

Fault Code 80: Both Arm-Up;Arm Down (Cam) Switches Closed...

SEQUENCE OF OPERATION

Ice Making Sequence

Ice Bin Full;Cleaning Mode

Water Plate Closure Problems

Shutdown-High Pressure

START METHODS

GT36 X, GT56 X, GB56 X WIRING DIAGRAM

GB1064 A & L WIRING DIAGRAM

GB106 XR WIRING DIAGRAM

COMPRESSOR TEST PROCEDURE

Test Procedure for a Short Circuit to Ground (Ground Fault)

Steps to test the compressor for ground faults.

Test Procedure for Continuity and Proper Resistance

Steps to test compressor winding continuity and resistance.

Test Procedure for Compressor Electrical Components

Testing potential relay, run capacitor, and start capacitor.

Testing The Potential Relay

Testing the Run Capacitor

Testing the Start Capacitor

Additional Service Information

WATER PLATE REPLACEMENT

WATER PLATE ALIGNMENT

WATER PLATE UP;DOWN POSITION AND ADJUSTMENT

ACTUATOR MOTOR ELECTRICAL TESTS

PROBE TEST PROCEDURE

Water Level Probes

Evaporator Temperature and Ice Level Probes

TROUBLE SHOOTING

STACKING INSTRUCTIONS

ICE CUBE CRUSHERS - T27 X

ICE CRUSHER-SAFETY INFORMATION

ICE CRUSHER INSTALLATION

Notes, warnings, and checklist for crusher installation.

Assembly;Installation

Steps for assembling and installing the crusher.

Initial Start-Up

ICE CRUSHER OPERATION

ICE CRUSHER CLEANING PROCEDURE

WIRING DIAGRAM

Wiring diagram for the ice crusher.

Pre-Install Checklist

PRE-CHARGED REMOTE AIR-COOLED CONDENSER - RC214 APV

PRE-CHARGED REMOTE AIR COOLED CONDENSER - INSTALLATION

Notes, warnings, and checklist for condenser installation.

Minimum Total Charge Required

Electrical Information

Kold-Draft GB1064AC Specifications

General

Model	GB1064AC
Type	Ice Maker
Condenser Type	Air-Cooled
Voltage	208-230V
Weight	390 lbs
Water Supply Connection	3/8" FPT
Refrigerant	R404A
Ice Production	1064 lbs per day