Konica Minolta bizhub 169 User Manual (English)

Questions and Answers:

D
Derrick BerryAug 25, 2025
Why are there streaks in my Konica Minolta bizhub 169 All in One Printer copies?
- A
  Andrew KruegerAug 26, 2025
  Streaks in copies from your Konica Minolta All in One Printer can occur for several reasons: * If you're copying a thin double-sided document, the information on the back might be showing through. In this case, press the [Density] key and select a lighter density setting. * The original glass may be dirty. Wipe it with a soft, dry cloth. * The document pad may be dirty. Clean it with a soft cloth dampened with a mild detergent. * If the original document is printed on highly translucent material, place a blank sheet of paper on top of the document.
C
Christina PowellAug 26, 2025
How to fix a Konica Minolta All in One Printer copy that is too light?
- S
  snyderkarenAug 26, 2025
  If your Konica Minolta All in One Printer is producing copies that are too light, it could be due to the copy density setting or the paper being used. * Check the copy density: Press the [Density] key and select a darker copy density. * Check the paper: If the paper is damp, replace it with new paper.
J
Jennifer WolfeAug 27, 2025
What to do if Konica Minolta bizhub 169 All in One Printer copy is too dark?
- E
  Evan WalterAug 27, 2025
  If your Konica Minolta All in One Printer is making copies that are too dark, there are a couple of things to check: * Copy Density: Make sure the copy density isn't set too dark. Press the [Density] key and select a lighter copy density. * Document Position: Ensure the document is pressed closely against the original glass.
P
Pamela FordAug 27, 2025
How to align image properly on Konica Minolta All in One Printer?
- C
  Caroline HartAug 27, 2025
  If the image is not aligned properly on the paper when using your Konica Minolta All in One Printer, consider the following: * Document Position: Ensure the document is correctly positioned against the document scales. * Document Feeder: If using the document feeder, lift it open and correctly position the document against the document scales. * Adjustable Guides: Slide the document guides against the edges of the document. * Paper: If curled paper was loaded into the paper drawer, flatten it before loading.
R
Robert Schultz MDAug 27, 2025
Why is my Konica Minolta bizhub 169 All in One Printer copy blurry?
- K
  Kendra AdamsAug 27, 2025
  A blurry copy from your Konica Minolta All in One Printer can be caused by: * Damp paper: Replace the paper with new paper. * Poor document contact: Position the document so that it is pressed closely against the original glass.
S
Sharon RossAug 28, 2025
Why Konica Minolta All in One Printer does not make copies when pressing start?
- C
  Carolyn McclainAug 28, 2025
  If your Konica Minolta All in One Printer isn't making copies even when you press the [Start] key: * Check the 'Error' indicator on the control panel. Follow the instructions in any messages that appear on the display. * If the machine was just turned on, wait until it has finished warming up.
Y
yjeffersonAug 28, 2025
What to do if nothing appears on Konica Minolta All in One Printer display?
- J
  johnsonjohnAug 29, 2025
  If nothing appears on the display of your Konica Minolta All in One Printer: * If only the indicator on the [Start] key is lit up in green, the machine has entered Power Save mode. Press any key in the control panel to cancel Power Save mode. * If the auto shut-off operation was performed, set the power switch to 'O'.
J
Joshua KellyAug 25, 2025
What to do if my Konica Minolta All in One Printer displays 'NOT ACCEPTED PASSWORD'?
- M
  Mary RobertsonAug 25, 2025
  The 'NOT ACCEPTED PASSWORD' message indicates that the secure print password you entered is incorrect, so the document cannot be printed. Type in the correct password.
J
Jay AndersonAug 30, 2025
What to do if Konica Minolta bizhub 169 All in One Printer does not enter Copy mode?
- R
  Ryan PalmerAug 30, 2025
  If your Konica Minolta All in One Printer does not enter Copy mode, check if the indicator on the [Interrupt] key is lit. If it is, press the [Interrupt] key to cancel Interrupt mode.
E
Edwin HenryAug 30, 2025
Why the start key indicator does not light up on Konica Minolta bizhub 169 All in One Printer?
- S
  Suzanne TurnerAug 30, 2025
  If the indicator on the [Start] key of your Konica Minolta All in One Printer does not light up, ensure the account number is entered according to the procedure described in 'Entering the account number'.