To Next PageTo Next Page
Need help?Do you have a question about the kozy heat MINNETONKA 55345 and is the answer not in the manual?
General| Brand | kozy heat |
|---|---|
| Model | MINNETONKA 55345 |
| Category | Indoor Fireplace |
| Language | English |
Critical advice on fire, explosion, and flammable vapors.
Step-by-step guide for handling gas leaks safely.
Specifies qualified personnel for installation and service.
Specific installation rules for the Commonwealth of Massachusetts.
Instructions to inspect all parts for damage or missing items before installation.
Key considerations like location, venting, and framing before starting installation.
Key measurements including height, front/back width, and depth.
Details specific access points for venting and electrical connections.
Specifies minimum safe distances from the fireplace to combustible surfaces.
Details minimum height and projection guidelines for mantels.
Guidance on installing hearths and extensions, including material considerations.
Defines minimum clearances for Dura-Vent and Selkirk Metalbestos chimney systems.
Illustrates common horizontal, vertical, and corner vent installation options.
Identifies compatible direct vent and flexible vent systems for the fireplace.
Specifies maximum vent lengths and rules for horizontal terminations.
Specifies maximum vent lengths and rules for vertical terminations.
Explains how adding elbows reduces the allowable vent system length.
General rules for vent termination placement and material considerations.
Detailed clearances required for vent terminations relative to structures.
Provides a chart detailing minimum chimney height based on roof pitch.
Warning against connecting this appliance to flues serving other appliances.
Specifies framing dimensions for horizontal vent termination openings.
Outlines clearance requirements for vertical vent pipe sections.
Emphasizes insulating the chase to prevent cold air entry into the room.
Specifies minimum finished opening dimensions for horizontal terminations.
Specifies minimum finished opening dimensions for vertical terminations.
Importance of front clearance for accessing controls, gas lines, and fans.
Instructions for forming and attaching the stand-off brackets to the fireplace.
Guidance on installing the horizontal vent heat shield for safety.
Step-by-step guide for placing the fireplace into its designated position.
Detailed instructions to safely remove the fireplace glass assembly.
Explains the use and placement of the restrictor plate for vertical venting.
Steps for installing the #800 Series Direct Vent Termination Kit.
Detailed steps for stretching, connecting flex pipes, and extension kits.
Instructions for installing the #800-WPT wall pass-thru for horizontal runs.
Guidance on when and how to install the fan kit for easier assembly.
Lists fan kit components and the basic wiring diagram for installation.
Lists components that need to be removed before installing the fan.
Step-by-step process for installing the fan assemblies and connecting their wiring.
Information on the fan assembly pre-installed and wired to the RF gas valve.
Steps for connecting the fan receptacle and completing its installation.
Safety precautions and guidelines for installing the gas line.
Provides inlet and manifold pressure, and orifice sizes for Natural Gas.
Provides inlet and manifold pressure, and orifice sizes for LP Gas.
Instructions to ensure the millivolt board is properly secured with screws.
How to adjust the intake shield for vertical termination height settings.
Detailed steps for positioning the 12 logs and embers correctly.
Guidance on placing rockwool burning embers and klinkers onto the burner.
Instructions for running low-voltage wires to wall switches or thermostats.
Guidance for installing and using the remote control assembly.
Steps for plumbing, leveling, and securing the fireplace to the framing.
Instructions on operating the heat damper control for desired heat output.
Steps to properly re-install the glass assembly onto the fireplace.
Instructions for installing the upper louver, hood, and lower grill.
Crucial safety checks and warnings to read before attempting to light the appliance.
Detailed steps for lighting the pilot assembly, including knob operation.
Procedures for safely turning off the main burner and the pilot light.
Information on the initial burn period, including expected discoloration and paint curing.
Steps to check the manifold pressure using a manometer.
Steps to check the incoming gas supply pressure using a manometer.
Crucial safety checks and warnings specific to the RF model before lighting.
Detailed steps for lighting the pilot assembly on the RF model.
Steps for initial transmitter recognition and pairing with the receiver.
Procedures for turning off the main burner, fan, and pilot.
Procedures for testing manifold and inlet gas pressures on the RF model.
Steps for performing a gas leak test using soap and water solution.
Recommendation for annual inspection by a professional service person.
Emphasizes keeping control compartments, burners, and air passageways clean.
Maintenance guidelines for the fan and annual examination of the vent system.
Important cautions regarding labeling wires and keeping area clear of flammables.
Safety precautions for handling hot components and protecting surfaces.
Detailed instructions for safely removing the millivolt board and its components.
Instructions for placing, securing, and aligning the millivolt board.
Guidance on setting the adjustable venturi to the 'LP Gas' position for easier installation.
Instructions for adjusting the venturi wheel position for LP Gas and Natural Gas.
Steps for re-installing pilot shield, logs, glass, and checking for gas leaks.
Solutions for problems like no spark or pilot not lighting.
Addresses issues where the pilot light fails to remain lit.
Solutions for when the main burner fails to ignite after the pilot is lit.
Solutions for when the main burner flame goes out unexpectedly.
Catalog of replacement parts for various fireplace components.
Details of the testing laboratory and the fireplace manufacturer.
Outlines warranty coverage for the first year and years 2 through 10.
Details limitations, exclusions, and conditions that void the warranty.
Conditions and requirements for making a warranty claim, including service records.
Details lifetime warranty coverage for specific fireplace components.
Instructions for completing and mailing the registration card for lifetime coverage.
