EasyManua.ls Logo

kozy heat SLAYTON-60 - User Manual

kozy heat SLAYTON-60
51 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Hussong Mfg. Co., Inc. • SLA-60 Report No: 0216GF048S • Rev. 1, September 2015
HUSSONG MANUFACTURING CO., INC.
ͷ Do not store or use gasoline or other
ammable vapors and liquids in the
vicinity of this or any other appliance.
ͷ WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do
not use any phone in your building.
• Leave the building immediately.
• Immediately call your gas supplier from
a neighbor’s phone. Follow the gas
supplier’s instructions.
• If you cannot reach your gas supplier,
call the re department.
ͷ Installation and service must be performed
by a qualied installer, service agency or
the gas supplier.
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly
could result in serious injury, death, or
property damage.
This appliance may be installed in
an aftermarket, permanently located,
manufactured home (USA only) or mobile
home, where not prohibited by local codes.
This appliance is only for use with the type
of gas indicated on the rating plate. This
appliance is not convertible for use with
other gases, unless a certied kit is used.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
SLAYTON-60
Model #SLA-60
Direct Vent Linear Gas Fireplace
Tested &
Listed By
OMNI-Test
Laboratories, Inc.
C US
Portland
Oregon USA
Installation and
Operation Manual
English and French installation manuals are
available through your local dealer. Visit our website
www.kozyheat.com or scan the QR code for our mobile app.
Les manuels d’installation en français et en anglais sont
disponibles chez votre détaillant local. Visitez
www.kozyheat.
com
ou scannez ce code QR pour notre application mobile.

Table of Contents

Questions and Answers

  • S
    Stephanie JonesAug 12, 2025
    What to do if the main burner flame will not light on my Kozy Heat Indoor Fireplace?
    • S
      Samuel AdamsAug 12, 2025
      If the main burner flame won't light, several factors could be at play. First, make sure the gas supply is turned on by checking for shut-offs in the supply line. If the gas supply is low, consult a plumber or gas supplier and check/refill the propane tank if necessary. Ensure the ON/OFF rocker switch is in the OFF position. Also, examine the wiring for disconnections or improper connections. If there's a blockage in the main burner orifice, remove it. Confirm the pilot flame is correctly directed to ignite the burner. If you're using a remote control, try replacing the batteries and ensure the remote control is powered ON and the thermostat operation is turned OFF.
  • R
    Robert LeeAug 15, 2025
    What to do if the pilot will not light on my Kozy Heat Indoor Fireplace?
    • D
      David MartinAug 15, 2025
      If the pilot light won't ignite, start by ensuring that electrical power to the appliance is restored or use a battery backup. Check for any wiring disconnections and use the wiring schematic to confirm all connections are secure and correct. If using a battery backup, ensure the batteries are fully charged. Verify that the ON/OFF/REMOTE selector switch is in the ON or REMOTE mode. Check that the gas supply is turned on by inspecting remote shut-off valves near the main gas line. Finally, confirm that the LP/NG switch on the control system is set to the correct gas fuel type.
  • K
    Katherine CollinsAug 20, 2025
    Why does the pilot and burner extinguish while in operation on my kozy heat SLAYTON-60 Indoor Fireplace?
    • C
      Claudia ShawAug 20, 2025
      Several factors can cause the pilot and burner to extinguish during operation. Check the propane tank and refill if necessary. Ensure correct installation of the glass assembly. Make sure the vent cap is correctly installed and free from blockages. Verify the horizontal venting has a ¼ inch rise per foot. Inspect the exhaust vent pipe for leaks, and repair if needed. The restrictor setting may need adjustment.
  • L
    Leah ReynoldsAug 23, 2025
    What to do if the pilot will not stay lit on my kozy heat SLAYTON-60 Indoor Fireplace?
    • B
      Betty FloresAug 23, 2025
      If the pilot light won't stay lit, first check the propane tank and refill it if necessary. Low gas pressure could also be the culprit, so consult a plumber or gas supplier, as this can be due to a bent line, a pipe with too narrow a diameter, or low line pressure. Also, make sure the pilot flame is making contact with the flame rectification sensor on the pilot assembly, enveloping the top of the flame sensor and extending far enough onto the burner for ignition.
  • C
    Christina CookeAug 27, 2025
    Why does soot appear on the glass of my kozy heat SLAYTON-60?
    • M
      martinezmarcusAug 27, 2025
      Soot appearing on the glass can be due to several reasons. Check the glass media placement. The venturi air shutter may need slight opening to allow more air into the gas mix. Inspect the vent cap for blockages and ensure it's correctly installed. Remove any debris if necessary.
  • M
    Michael WeaverAug 31, 2025
    What to do if there is no reaction to command on my Kozy Heat Indoor Fireplace?
    • B
      Brett GreenAug 31, 2025
      If your fireplace isn't responding to commands, start by replacing the batteries in the battery backup or remote control. If that doesn't work, there may be no communication between the remote control and the control module. If a maximum number of failed ignitions or flame restorations has been reached, reset the Komfort 8K1 control module.
  • S
    Sheryl TrujilloSep 3, 2025
    Why is the pilot flame always on, or will not extinguish on my Kozy Heat Indoor Fireplace?
    • K
      Kimberly WeberSep 3, 2025
      If the pilot flame is always on or won't extinguish, the control system might be set to Pilot-on-Demand ignition mode. You should set the control system to intermittent pilot ignition mode.
  • J
    Jodi NormanSep 7, 2025
    Why does the flame burn blue and lift off burner on my Kozy Heat Indoor Fireplace?
    • D
      David GarciaSep 7, 2025
      If the flame burns blue and lifts off the burner, it could be due to an improper venturi setting, meaning the venturi air shutter may need to be opened slightly to allow more air into the gas mix. Another potential cause is incorrect vent cap installation. Also, check the vent pipes for leaks and the vent cap for debris, repairing the vent pipes or removing debris from the vent cap if necessary.

Summary

1.0 Introduction

1.2 Massachusetts Installation Requirements

Specific rules for MA including CO detectors, signage, and manufacturer obligations.

2.3 Appliance Dimensions

3.0 Framing

3.1 Appliance Placement Considerations

Guidelines for choosing a safe and appropriate location for the fireplace.

3.3 Clearances to Combustibles

3.4 Wall Enclosure Rough Opening

5.1 Nailing Flange Assembly and Installation

5.2 Facing Requirements

5.3 Mantel Requirements

6.0 GAS LINE CONNECTION

6.2 Gas Line Installation

Procedures for installing the gas line, including safety precautions and pressure requirements.

7.0 TERMINATION LOCATIONS

7.1 Vertical Vent Cap Termination

Specifies requirements and clearances for vertical vent cap placement.

7.2 Minimum Termination Clearances

8.5 Vertical Terminations

8.6 Combination Venting

8.6.1 Natural Gas Installations

Requirements for combination venting with natural gas, including horizontal rise.

8.6.2 LP Gas Installations

8.7 #800-1 Series Direct Vent Termination Kit(s)

8.7.1 Assembly and Installation

Step-by-step guide for assembling and installing the #800-1 Series termination kit.

9.4 Control Board Removal and Installation

9.4.1 Control Board Removal

Step-by-step guide for safely removing the control board.

9.4.2 Control Board Installation

Step-by-step guide for correctly installing the control board.

11.0 OPERATING INSTRUCTIONS

Safety and Startup Procedures

Crucial safety warnings, gas leak checks, and initial startup steps.

Standard Operating Procedure

Step-by-step guide to start the fireplace using the remote and manual valve.

Turning Off Gas to Appliance

11.1-11.5 IFC Module Setup and Control

11.1 Setup and Initialization

Guide to setting up the Proflame 2 IFC module and initializing the control system.

11.6-11.7 IFC Module Ignition and Diagnostics

11.6 IFC Module Ignition Sequence

Details the ignition process and lockout conditions.

11.8.4-11.8.7 Appliance Control and Thermostat

11.8.7 Thermostat Operation

12.0 ADJUSTMENT

12.1 Pressure Testing

Procedures for testing inlet and manifold gas pressures.

12.2 Flame Appearance Adjustment

12.2.1 Burner Venturi Adjustment

Instructions for adjusting the burner venturi for optimal flame appearance.

12.2.2 Vent Restriction

13.0 TROUBLESHOOTING

Limited Warranty

10 Year Limited Warranty Details

Terms, conditions, and limitations of the 10-year limited warranty.

Warranty Conditions and Liability Limitations

Requirements for coverage and liability exclusions.

LIFETIME WARRANTY

Lifetime Warranty Coverage

Details lifetime warranty for specific fireplace components and its limitations.

Limitation of Liability

Explains limitations and remedies for the lifetime warranty.

kozy heat SLAYTON-60 Specifications

General IconGeneral
Brandkozy heat
ModelSLAYTON-60
CategoryIndoor Fireplace
LanguageEnglish

Related product manuals