What to do if KRESS Mission RTKn 5000 MissionTM RTKn does not work after pressing the start button?
If your KRESS Lawn Mower MissionTM RTKn doesn't start after pressing the start button, it might be outside the working area. Move it inside the working area. Alternatively, the positioning signal may be poor. In that case, move the mower to an open place, wait for the positioning signal light to turn green, and then press the start button.
Why KRESS Lawn Mower runs out of power but does not return to charging base?
If your KRESS Lawn Mower runs out of power and doesn't return to the charging base, it could be due to a missing virtual charging base mapping. Rebuild the map and add the virtual charging base. Another reason might be that the magnetic strip is shorter than 2.5 m, ensure that it is longer than that.
What to do if KRESS Mission RTKn 5000 Lawn Mower MissionTM RTKn is parked in the middle of the obstacle?
If your KRESS Lawn Mower MissionTM RTKn gets stuck in the middle of an obstacle, it could be because the obstacles are too small for it to navigate out. Set the area where MissionTM RTKn is easily trapped as a No-Go zone. Alternatively, the mower's sensor may be malfunctioning. Check the sensor status on the diagnostic page in the app.
What to do if KRESS Lawn Mower MissionTM RTKn does not give an alarm when it is outside the Geo fence?
If your KRESS Lawn Mower MissionTM RTKn isn't alarming when outside the Geo fence, the software might be outdated; update the software. Also, ensure that the MissionTM RTKn is powered on.
How to fix KRESS Lawn Mower MissionTM RTKn that cannot correctly dock with the charging base?
If your KRESS Lawn Mower MissionTM RTKn is having trouble docking with the charging base, check the magnetic strip. If it's placed incorrectly, the green stripe should face away from the charging base.
Why KRESS Mission RTKn 5000 MissionTM RTKn is parked around the wall and cannot be started?
If your KRESS Lawn Mower MissionTM RTKn is parked near a wall, won't start, and the positioning light stays red, it might be due to the mower working in a shaded area for too long, which triggers a safety protection. Try to avoid mowing in heavily shaded areas.
What to do if KRESS Mission RTKn 5000 LED light on the charging base does not turn on?
If the LED light on the charging base of your KRESS Lawn Mower isn't turning on, it's likely due to a power issue. Check that the charging base is correctly connected to the charger and that the charger is plugged into a working power supply.
What to do if KRESS Mission RTKn 5000 MissionTM RTKn overruns the boundary line when going downhill?
If your KRESS Lawn Mower MissionTM RTKn overruns the boundary line when going downhill, this may be because the angle of the border line is very sharp. Try to avoid layout scenarios with sharp angles.
Read all safety warnings and instructions. Failure to follow may result in electric shock, fire, or serious injury.
Read instructions carefully, understand controls, and be familiar with proper appliance use.
Confirm virtual boundary is established and maintained. Machine checks boundary before each working cycle.
Keep nuts, bolts, and screws tight. Inspect the lawnmower weekly and replace worn parts.
Use original packaging for long distances. Use STOP button and switch off before carrying.
Do not dismantle, open, shred, or short-circuit the battery pack. Keep it clean and dry.
Operation is subject to conditions: no harmful interference and acceptance of received interference.
The garden product is intended for domestic lawn mowing, maintaining a healthier and better-looking lawn.
Clean and check the Mission™ RTK regularly. Switch off before carrying out any service or maintenance.
Blades need reversing monthly and replacing weekly. Always replace all blades and use new screws.
Clean the machine body regularly using a soft brush or clean cloth, avoiding solvents or polishes.
Flip the machine upside down, clean the blade disc, chassis, and wheels with a soft brush or moist rag.
Clean contact pins and charging strips on the base and mower to ensure successful charging.
Connect charging base, manually dock the mower when powered off, and ensure green light is flashing.
Turn mower upside down, remove battery cover screws and battery cover.
Turn mower upside down, remove battery cover and sheet metal screws.
Remove battery pack safely before disposing of appliance. Dispose of at a dedicated recycling facility.
Read all safety warnings and instructions. Failure to follow may result in electric shock, fire, or serious injury.
Read instructions carefully, understand controls, and be familiar with proper appliance use.
Confirm virtual boundary is established and maintained. Machine checks boundary before each working cycle.
Keep nuts, bolts, and screws tight. Inspect the lawnmower weekly and replace worn parts.
Use original packaging for long distances. Use STOP button and switch off before carrying.
Do not dismantle, open, shred, or short-circuit the battery pack. Keep it clean and dry.
Operation is subject to conditions: no harmful interference and acceptance of received interference.
The garden product is intended for domestic lawn mowing, maintaining a healthier and better-looking lawn.
Clean and check the Mission™ RTK regularly. Switch off before carrying out any service or maintenance.
Blades need reversing monthly and replacing weekly. Always replace all blades and use new screws.
Clean the machine body regularly using a soft brush or clean cloth, avoiding solvents or polishes.
Flip the machine upside down, clean the blade disc, chassis, and wheels with a soft brush or moist rag.
Clean contact pins and charging strips on the base and mower to ensure successful charging.
Connect charging base, manually dock the mower when powered off, and ensure green light is flashing.
Turn mower upside down, remove battery cover screws and battery cover.
Turn mower upside down, remove battery cover and sheet metal screws.
Remove battery pack safely before disposing of appliance. Dispose of at a dedicated recycling facility.
The Kress Mission RTK is a robotic lawnmower designed for domestic lawn care, aiming to maintain a healthier and better-looking lawn. It operates autonomously, navigating a defined work area to cut grass efficiently. The device is part of the Kress Robotik product line, emphasizing advanced technology for lawn maintenance.
The Kress Mission RTK is a sophisticated robotic lawnmower that utilizes RTK (Real-Time Kinematic) technology for precise navigation. This allows the mower to operate within a virtual boundary, which it checks before each working cycle. If the virtual boundary is not detected, the machine will shut down. The RTK antenna on the machine senses when it approaches this virtual boundary or encounters an obstacle, prompting it to select a new direction. This system ensures the mower stays within its designated work area and avoids collisions.
The mower is equipped with razor-sharp cutting blades that rotate in both directions to maximize cutting capacity. The redesigned blade profile helps prevent grass clippings from getting caught. It can be programmed to operate at specific times and frequencies, depending on the lawn size, offering flexibility to the user. The device is not intended for other tasks such as digging, sweeping, or snow cleaning.
For safety, the Mission RTK includes a disabling device that should be operated before clearing blockages, checking, cleaning, or performing any work on the appliance. It also features a STOP button for immediate cessation of operation. The lawnmower should never be operated without its guard in place.
The device is powered by a 20V Li-Ion battery, which can be charged manually by docking the mower into its charging base. The charging base has a green light indicator that turns on when connected to power and flashes when the mower is charging. The battery life is influenced by factors such as the length of the mowing season, daily operating hours, and battery maintenance during storage.
Operating the Kress Mission RTK involves several key steps and considerations. Users must first establish and regularly maintain the virtual boundary that defines the mower's work area. Before each use, it's recommended to inspect the area for any foreign objects like stones, sticks, wires, or bones that could interfere with the mower's operation.
The mower should only be used by individuals familiar with its operation and safety instructions. Children and people with reduced physical, sensory, or mental capabilities should be supervised or instructed by a responsible person. It is crucial never to allow people unfamiliar with the instructions to use the appliance.
When operating, users must keep hands and feet away from rotating parts and the discharge opening. The mower should never be picked up or carried while the motor is running. For automatic operation, the machine should not be left unattended if pets, children, or people are in the vicinity.
The Mission RTK is designed for frequent mowing to maintain lawn health. Its operation can be customized through programming, allowing users to set specific times and frequencies. The device is equipped with an ultrasonic sensor (on specific models) for enhanced obstacle avoidance, further improving its autonomous navigation capabilities.
In case of abnormal vibration or striking a foreign object, the machine should be inspected for damage before restarting. Modifications to the original design of the robotic lawnmower are not permitted and are done at the user's own risk. The mower will only start when the power is on and the correct PIN code has been entered.
Regular maintenance is crucial for the longevity and optimal performance of the Kress Mission RTK. Before any cleaning, adjusting, or blade replacement, the mower must be turned OFF, and protective gloves should be worn.
Blade Maintenance: The cutting blades typically need to be reversed monthly and replaced weekly, though this frequency can be adjusted based on cutting quality. When replacing blades, all blades and screws should be replaced simultaneously to ensure balance and proper blade retention. It's important to ensure the new blades are firmly screwed on and can spin freely. For models with dual-layer blades, a specific procedure involving removing the battery cover, battery, and blade disc is required.
Cleaning: The mower's body should be cleaned regularly using a soft brush or moist rag, avoiding solvents or polishes. Hose water cleaning is supported, but high-pressure washers should never be used, as water can damage electronic and mechanical parts. The underside, including the blade turning disc, chassis, and wheels, should be thoroughly cleaned with a soft brush or moist rag. It's vital to remove any stuck debris from the blade disc to prevent cracks, which can impair mowing output. The contact pins on the charging base and the charging strips on the mower should also be cleaned periodically with a cloth to ensure proper charging.
Battery Care: The 20V Li-Ion battery should be fully charged and stored in a cool, dry place (-20°C to +60°C) for proper storage. For winter hibernation, the mower should be thoroughly cleaned, the battery fully charged, and the power turned off. Before bringing the mower back into service after winter, ensure the charging strips and contact pins are clean, using fine-grade emery cloth if necessary. The app can be used to verify date and time settings.
General Maintenance: All nuts, bolts, and screws should be kept tight to ensure safe working condition. The robotic lawnmower should be inspected weekly, and worn or damaged parts should be replaced for safety. Only replacement cutting means of the correct type should be used. Servicing should always be done according to the manufacturer's instructions.
Transport: For long-distance transport, the original packaging should be used. When moving the mower within or from the working area, press the STOP button, switch off the mower if carrying it, and carry it by the handle at the rear, keeping the blade disc away from the body.
The Kress Mission RTK is designed to be user-friendly in its maintenance, with clear instructions for common tasks to ensure its longevity and efficient operation.
General| Recommended Lawn Size | 5000 m² |
|---|---|
| Maximum Slope | 45% |
| Cutting Height | 30-60 mm |
| RTK Technology | Yes |
| Weight | 22.5 kg |
| Motor Type | Brushless |
| Power Source | Battery |
| Obstacle Avoidance | Yes |
| Grass Collection Bag Capacity | No grass collection bag |
To Next Page
