41 44
EN
Q: The projector has been exposed to rain during
an outdoor show without the Rain Cover installed.
What shall Idonext?
A: It is necessary to remove the laser projector from its
flight case as soon as possible - within 24 hours at the
latest after the show, and let both projector and flight case
fully dry out.
NEVER turn ONthe projector before itis100% dry inside
out.
When ready, please check the status ofthe anti-humidity
cassette containing silica gel. For more information about
this topic, go to the User manual (chapter Maintenance).
Insucient drying of the projector and its flight-case
can cause permanent damage to the projector (mould,
corrosion) and voids the warranty. Powering up wet
ordump projector can cause electrical shock, injury, orfire
risk. Itcan also cause permanent damage tothe projector,
inwhich case the warranty isvoided.
Q: Is the Rain cover accessory suitable for long term
protection against outdoor weather conditions?
A: No. The Rain cover was designed as emergency
protection against rain or snow for short term outdoor
use. During intense precipitation and winds, it can
get soaked with water. Therefore, removing the
rain cover from the projector after every use and
letting it dry together with the projector is necessary.
Insucient drying of the projector and its flight-case
can cause permanent damage to the projector (mould,
corrosion) and voids the warranty. Powering up wet
ordump projector can cause electrical shock, injury, orfire
risk. Itcan also cause permanent damage tothe projector,
inwhich case the warranty isvoided.
Q: Is it possible to use the Rain cover for a projector
that is set other than horizontally (i.e. when projecting
upwards)?
A: No. Our Rain cover works eciently ONLY for projectors
set inahorizontal position - that’swith rubber feet towards
the ground.
Ifthe Rain cover isused any other way, itwon’tprotect your
equipment.
Q: Atlow temperatures, the laser projector won’tstart.
A: The operating temperature range for Kvant laser
projectors is+10°C(50°F) to+35°C(95°F).
If used outside of this range, we recommend
using the Kvant Monsoon. This robust and durable
enclosure will protect your delicate equipment,
such as laser projectors, against harsh weather
conditions, extreme temperatures and high humidity.
As a temporary solution, you can use an electric heater
topre-heat the air entering the laser projector. Place the
heater atthe correct distance from the projector, sowhen
the air enters the laser projector, it is within the range
+10°C(50°F) to+25°C(77°F). The projector may get damaged
ifthe heater isplaced too close tothe projector’sairflow
inlets orrear control panel.
Q: Laser projector stops working or even won’t start
athigh ambient temperatures.
A: The operating temperature range for Kvant laser
projectors is+10°C(50°F) to+35°C(95°F). Using projectors
inanenvironment with air temperatures within 35°C (95°F)
to45°C(113°F) isnot harmful tothe projector, but limits its
ability todisperse the heat eciently, resulting inlowered
nominal power output orcomplete cuto.
There isarisk ofpermanent damage tothe laser
projector ifused intemperatures exceeding 45°C(113°F),
inwhich case the warranty isvoided.
Never place and use projectors near objects that
generate excessive heat, such asradiators, powerful
discharge lighting, orwarm air outlets.
For the use intemperatures exceeding 35°C(95°F),
installing the projector into the Monsoon box with abuilt-
inACunit ishighly recommended.
Asatemporary solution, you can use asmall ACunit and
direct it’soutput towards the projector’sintake fans.
Q: Is it possible to do modifications to the electronic
circuitry ofthe laser projectors?
A: Itisnot allowed tomodify the electronic circuitry
oflaser projectors without prior authorization and
approval ofKvant’stechnical support representative.
Any unauthorized modifications will result inimmediate
warranty termination.
There isarisk ofelectric shock and the risk ofinjury
orproperty damage bylaser radiation. Unauthorized
modifications ofthe circuitry may cause achange inthe
projector’sfunctionality and specifications, making
itincompliant with regulations and standards ofClass
IVlaser devices.
Q: What ifIfeel asmall electric shock when touching the
metal parts ofthe projector’shousing?
A: Turn o the projector immediately. Disconnect the
projector from the AC mains power supply. A qualified
electrician must check the mains power cable and the
socket.
The two common reasons are:
1. Too long AC mains power cable with joined cables
N(blue) and PE(yellow-green). The 3-wire connection
isessential.
2. Disconnected, not connected, orinterrupted PEwire
inACmains power cable orACwall plug.
Q: What if I feel a pretty strong electric shock when
touching the metal parts ofthe projector’shousing?
A: There is a danger of fatal electric shock! Turn o the
projector immediately. Disconnect the projector from the
ACmains power supply. Aqualified electrician must check
the mains power cable and the socket.