ENGLISH
A B C
M
S
J
R (3x)
If needed, re-key the lock to
work with your existing key.
See the supplied SmartKey
Re-key instructions for more
information.
ball
tip
Keep “S” in a safe place, as you will
need it to access the back panel for
additional programming.
Install the battery cover and re-key the lock
A B
L
Press and hold the
Lock button while
installing battery
pack (L).
Hold button until the
latch bolt starts
moving on its own.
This step will teach your lock the orientation of your door
and is crucial to lock operation.
HOLD
latch bolt
Did the latch bolt retract
and extend on its own
when the battery pack
was installed?
Door handing process
was successful! Proceed
to Step 10 after latch bolt
stops moving.
Remove battery pack,
wait 15 seconds, then
attempt the process
again.
YES NO
Perform door handing process
Program the lock
Programming
instructions are
located on the
reverse side of
this document.
B
D (2x)
Install strike
A / A2
Extend latch bolt
E
F
G
G
2-1/8"
54 mm
1-1/2"
38 mm
Prepare exterior keypad
For doors with 2-1/8" (54 mm) holes
For doors with 1-1/2" (38 mm) holes
A B
C D
K
Q (2x)
Q
H
Cable goes
underneath latch
Route cable
through center hole,
then push cable
into side hole.
center hole
side hole
Keep parallel to
edge of door
Tighten
screws
evenly
Insert key and test latch.
If latch does not extend or
retract smoothly, adjust
screws (Q).
Remove key when nished
and make sure the latch
bolt is fully extended.
Install keypad and mounting plate
A
D
B C
N
M
L
x4
AA
L
Make sure
turnpiece is
in the vertical
position.
Disassemble interior assembly and load battery pack
Ensure correct polarity. For best results,
use new non-rechargeable Alkaline
batteries only.
Do not install
battery pack yet!
Use and programming
instructions are located on the
reverse side of this document.
Required Tools
Additional Tools (depending on application)
Installation Guide
180°
A B
A / A2
Hold the latch in front of the
door hole, with the latch face
ush against the door edge.
If the latch holes are
centered in the door hole, no
adjustment is required.
Proceed to step 4.
If the latch holes are NOT
centered, adjust latch. See
“Latch Adjustment.”
Latch Adjustment (only if needed)
Adjust the backset of latch (if needed)
A
A2
C (2x)
A
B
C D
Install latch
For doors with chiseled edge For doors without chiseled edge
wood
block
1-3/4" (44 mm)
1-3/8" (35 mm)
2-1/4" (57 mm)
2-3/8" (60 mm)
2-3/4" (70 mm)
Fold
If your door requires drilling, cut out the template and place it on the exterior side of the door.
Complete door drilling instructions are available on the SmartCode deadbolt page of www.kwikset.com.
Template
Edge
Backset
Face
Centerline
9
10 11 12
A C DB
N
P (2x)
K
Ensure tight cable connection.
Lay cable
at against
the interior
housing.
Install interior assembly
A
A2
B
C
D
E
F
G
H
K
L
M
N
P
Q
S
R
J
Kwikset
1-800-327-5625
www.kwikset.com
If needed, please contact
Kwikset to order a drive-in
latch for your lock.
Parts in the Box
Latch and Strike Exterior Assembly Interior Assembly
1"
25 mm
2-1/8"
54 mm
1-1/2"
38 mm
1-3/8" — 1-3/4"*
35 mm — 44 mm*
Check dimensions
Additional door preparation may be
required for doors with 1-1/2" (38 mm)
holes. Consult the drilling instructions at
www.kwikset.com/doorprep.
*Service kits for 2-1/4"
(57 mm) thick doors are
available through Kwikset.
2-3/8" (60 mm)
or
2-3/4" (70 mm)
or
3 4 5 6
7 8
1 2
60730 / 01
To Next Page
Need help?
General
