LECAI Science And Technology LC Easyjet-16W

Questions and Answers

K
kelly73Aug 17, 2025
Why is my LECAI Science And Technology LC Easyjet-16W printing ink-break?
- L
  Lauren YoungAug 17, 2025
  Print ink-break can occur due to several reasons: 1. The print head may need cleaning. 2. The working environment might not be suitable: the optimal temperature is between 18° and 35°C, and humidity should be between 35%RH and 65%RH. 3. Voltage instability can be a factor, so using a UPS is advisable. 4. The ink tube might have air leaks or be folded. 5. The air hole of the ink cartridge could be blocked. 6. The damper may need ink or replacement. 7. Using LECAI original Ink is recommended. 8. The Carriage board may need replacement.
T
Timothy SkinnerAug 20, 2025
What to do if LECAI Science And Technology LC Easyjet-16W output form Maintop but printer no response?
- A
  Aaron VasquezAug 20, 2025
  If your printer isn't responding when outputting from Maintop, consider the following: 1. Ensure the PC IP address is set to 196.12.0.188. 2. Try changing the network cable. 3. Set up the printer in Maintop. 4. Click the “Start” icon in Maintop Manager to initiate printing. 5. Reinstall the Maintop software. 6. Try using another computer. 7. Consider changing the mainboard.
W
Wendy WilliamsAug 22, 2025
Why LECAI Science And Technology LC Easyjet-16W printing pass line?
- J
  jonathangarciaAug 23, 2025
  Printing pass lines can be caused by: 1. Calibration issues, which can be resolved by step calibration. 2. A feeding unit that is too tight, preventing automatic media feeding. 3. The print head may need cleaning. 4. The X motor belt tensioning may need adjustment. 5. Enabling the “Eclosion” function may help.
M
Michael SmithAug 26, 2025
Why LECAI Science And Technology LC Easyjet-16W print size not correct?
- L
  Laura BuchananAug 26, 2025
  Incorrect print size can stem from: 1. Calibration issues; calibrate the printer. 2. Incorrect image size; check the image size. 3. Problems with Maintop software; reinstall it. 4. A dirty Raster; clean it. 5. The X motor belt tensioning may need adjustment. 6. A feeding unit that is too tight, preventing automatic media feeding.
S
swhiteAug 28, 2025
What to do if LECAI Science And Technology LC Easyjet-16W Printer print misting?
- A
  Amy PhillipsAug 28, 2025
  Print misting can occur due to: 1. Static; connect the earth lead and test with a multimeter. 2. The media; try using other media. 3. Voltage fluctuations; use a UPS. 4. Incorrect print head height; adjust it to about 1.5mm. 5. Unsuitable working environment; ensure the temperature is between 18° and 35°C and humidity is between 35RH and 65RH.
J
Jennifer WillisAug 31, 2025
What to do if LECAI Science And Technology Printer turn on but the LCD can’t show?
- J
  James FoleyAug 31, 2025
  If the LCD doesn't display when you turn on the printer, check the following: 1. Try changing the power cable. 2. Re-plug in the LCD cable. 3. Test with a multimeter to see if there is voltage. 4. Change the mainboard fuse. 5. Check whether the transformer has voltage. 6. Check the mainboard power cable. 7. Change the mainboard. 8. Change the LCD.
D
Diana ReyesSep 2, 2025
What to do if LECAI Science And Technology Printer carriage rushes out from the station and rushes back?
- L
  Lance PetersonSep 2, 2025
  If the carriage rushes out from the station and then rushes back, consider these steps: 1. Check the raster sensor position. 2. Change the raster sensor. 3. Clean the raster. 4. Change the raster.
T
Troy BakerSep 5, 2025
What to do if LECAI Science And Technology LC Easyjet-16W turn on but Carriage can’t move?
- K
  Kenneth MartinSep 5, 2025
  If the carriage won't move after turning on the printer, try these solutions: 1. Re-plug in the motor cable. 2. Re-plug in the Operation panel cable. 3. Change the mainboard fuse. 4. Change the mainboard. 5. Change the Motor.
Y
Yolanda Davis MDSep 8, 2025
Why LECAI Science And Technology LC Easyjet-16W media skew during printing?
- L
  Lisa MccoySep 8, 2025
  Media skew during printing can be caused by: 1. The feeding unit; check whether it is working smoothly. 2. The media itself; try reloading it and setting it in the correct position. 3. The pinch rollers; ensure all of them grip the media properly.
D
darinperezSep 12, 2025
What to do if LECAI Science And Technology Printer heating but no response?
- A
  Alexandria GonzalezSep 12, 2025
  If the printer is heating but not responding, check these: 1. See whether the heater switch is damaged. 2. Check whether the heater cable is loose. 3. Try increasing the temperature from the temperature controller. 4. Change the temperature controller. 5. Change the heater.