Why does my Lenze AC Tech SF210 show a Current Overload Fault?
A Current Overload Fault in your Lenze AC Tech Controller indicates that the VFD is undersized for the application or there is a mechanical problem with the driven equipment.
What causes an Output Transistor Fault in Lenze AC Tech SF210 Controller?
An Output Transistor Fault in your Lenze AC Tech Controller can be triggered by a phase-to-phase or phase-to-ground short circuit on the output, a failed output transistor, boost settings that are too high, or an acceleration rate that is too fast.
What causes a Low DC Bus Voltage Fault in Lenze AC Tech SF210?
A Low DC Bus Voltage Fault in your Lenze AC Tech Controller is caused by line voltage that is too low.
What to do if Lenze AC Tech SF210 Controller displays a Control Fault?
If your Lenze AC Tech Controller displays a Control Fault, it may be due to a blank EPM or an EPM with corrupted data. Perform a factory reset using Parameter 48 - PROGRAM SELECTION.
How to resolve Incompatibility Fault on Lenze AC Tech Controller?
An Incompatibility Fault on your Lenze AC Tech Controller indicates that an EPM with an incompatible parameter version has been installed. You can either exchange the EPM or perform a factory reset (Parameter 48) to change the parameter version of the EPM to match the parameter version of the drive.
What does Single-phase Fault mean on Lenze AC Tech Controller?
A Single-phase Fault on your Lenze AC Tech Controller means that single-phase input power has been applied to a three-phase drive.
Why does my Lenze AC Tech Controller show a Start Fault?
A Start Fault on your Lenze AC Tech Controller occurs when a start command was present when the drive was powered up. You must wait 2 seconds after power-up to apply the Start command if START METHOD is set to NORMAL.
What does External Fault mean on Lenze AC Tech SF210?
An External Fault occurs on your Lenze AC Tech Controller when TB-13A and/or TB-13C is set as an External Fault input and TB-13A and/or TB-13C is open with respect to TB-2. Refer to Parameter 10 or 12.
What causes a Data Fault in Lenze AC Tech SF210?
A Data Fault in your Lenze AC Tech Controller indicates that user data and OEM defaults in the EPM are corrupted.
What does Serial Fault mean on Lenze AC Tech SF210?
A Serial Fault indicates that the watchdog timer has timed out, meaning the serial link has been lost on your Lenze AC Tech Controller.
Defines signal words and icons used to convey safety information and warnings.
Safety precautions for electrically live parts, hot surfaces, and potential hazards.
Observe national safety regulations and EMC compliance for electrical installations.
Lists environmental, electrical, and performance specifications for the SCF drive.
Provides rating tables for motors, input/output current, and heat loss.
Drives must not be installed in adverse environmental conditions.
Safety and programming notes for AC power input.
Requirements for circuit breakers, fuses, and disconnect switches.
Capacitors retain charge; wait before servicing power wiring.
Instructions for single/three-phase inputs and motor output wiring.
Diagrams for three-phase and single-phase power wiring connections.
Do not connect AC power to output/DC bus terminals; wire/ground as per codes.
Programming TB-13B for Jog Forward/Reverse; safety warning.
Electrical shock hazard; wait before servicing power connections.
Procedure to verify motor rotation after initial power up.
Describes programming using buttons, EPM, or serial link.
Do not remove EPM while power is applied; drive needs EPM to operate.
Lists parameters, their range of adjustment, and factory defaults.
Details parameters for voltage, frequency, start/stop methods.
Details parameters for speed source, outputs, and function select.
Details parameters for analog outputs and function selects.
Explains different drive start methods (Normal, Power Up, DC Brake, Flying Restart).
Explains different drive stop methods (Coast, DC Brake, Ramp).
Sets the time to accelerate from 0 Hz to BASE FREQUENCY.
Sets the time to decelerate from BASE FREQUENCY to 0 Hz.
Sets adjustable thermal overload protection for the motor.
Sets output frequency at which drive outputs full voltage to motor.
Selects operation mode (User/OEM) or resets parameters to defaults.
Accessing parameters 50-60 for troubleshooting without password.
Lists fault conditions, possible causes, and clearing procedures.
Describes the PI Setpoint Control software option and its parameters.
Details PI-specific parameters like TB-13 function select and PI MODE.
Details PI parameters like MIN/MAX FEEDBACK and gain settings.
Details PI parameters like PROPORTIONAL GAIN, INTEGRAL GAIN, PI ACCEL/DECEL.
Details PI parameters like MIN/MAX ALARM and feedback monitoring.
Procedures for tuning PI control using Proportional and Integral Gain.
General| Output Voltage | 0-Input Voltage |
|---|---|
| Output Frequency | 0-400 Hz |
| Input Frequency | 50/60 Hz |
| Enclosure Type | IP20 |
| Operating Temperature | 0-40°C (32-104°F) |
| Storage Temperature | -20°C to +65°C |
| Humidity | 5-95% (non-condensing) |
| Protection Features | Overcurrent, Overvoltage, Undervoltage, Overheating, Short Circuit |
To Next Page
