What does earth fault mean on Lenze ESMD153L4TXA Inverter?
If the Lenze Inverter indicates an earth fault, it could be due to: * A grounded motor phase: Inspect the motor and motor cable. * Excessive capacitive charging current of the motor cable: Use shorter motor cables with a lower charging current.
Why Lenze DC Drives show earth fault?
An earth fault in Lenze DC Drives can occur if a motor phase is grounded, so you should check the motor and motor cable. It can also be due to excessive capacitive charging current of the motor cable, in this case use shorter motor cables with lower charging current.
What to do if Lenze DC Drives have controller overtemperature?
If the controller has an overtemperature, it means the controller is too hot inside. To resolve this, reduce the controller load and improve cooling.
What to do if Lenze DC Drives show undervoltage on DC bus?
If Lenze DC Drives show undervoltage on the DC bus, it could be because the mains voltage is too low. Check the mains voltage.
How to resolve dynamic braking fault in Lenze DC Drives?
A dynamic braking fault in Lenze DC Drives typically means that the dynamic braking resistors are overheating. To resolve this, increase the deceleration time.
What to do if Lenze DC Drives have a single phase fault?
If Lenze DC Drives have a single phase fault, it means a mains phase has been lost. Check the mains voltage.
What to do if Lenze DC Drives have a communication error?
If Lenze DC Drives have a communication error, it may be because the serial timer has timed out. Check the serial link connections.
What to do if Lenze Inverter shows short-circuit or overload?
If the Lenze Inverter experiences a short-circuit or overload, there are several potential causes: * A short-circuit itself: Investigate the cause and inspect the motor cable. * Excessive capacitive charging current: Use shorter motor cables. * Acceleration time is too short: Increase the acceleration time and check the controller selection. * Defective motor cable: Check the wiring. * Internal fault in the motor: Check the motor. * Frequent and long overload: Check controller selection.
Why is my Lenze ESMD153L4TXA showing overvoltage on DC bus?
If your Lenze Inverter is experiencing an overvoltage on the DC bus, it could be due to several reasons: * The mains voltage might be too high: Verify the mains voltage. * The deceleration time might be excessively short, or the motor might be in generator mode: Increase the deceleration time or consider using a dynamic braking option. * Earth leakage on the motor side: Check the motor and motor cable, separating the motor from the controller to diagnose.
What causes motor overload on Lenze Inverter?
If the Lenze Inverter displays a motor overload (I2t overload), it means the motor is thermally overloaded. This can be due to: * Impermissible continuous current. * Frequent or excessively long acceleration processes. To resolve this: * Check the controller selection. * Check the setting of c20.
General safety precautions for Lenze controllers, covering risks from live parts and hot surfaces.
Guidelines for using drive controllers in machines and compliance with EC directives like Machinery Directive.
Proper handling, avoiding mechanical stress, and preventing damage to electronic components during installation.
Observing national regulations and appropriate procedures for electrical installation, including cable and PE connection.
Ensuring systems have monitoring/protection devices and following operational safety rules like closing covers.
Policy on using inverter products with explosion proof motors, including liability and risk assumption.
Explanation of pictographs (Danger, Warning, Stop, Note) and their consequences if ignored.
Conformity, approvals, environmental conditions, and operating parameters for the inverter.
Electrical ratings including input voltage, current, and output current for various inverter models.
Guidelines for physical mounting, dimensions, and environmental considerations for the inverter.
Procedures for wiring, EMC requirements, fuses, cable cross-sections, and connection diagrams.
How to navigate the controller interface to set and change parameters.
Information about the EPM for storing, transferring, and managing parameter settings.
Detailed description of parameter codes, possible settings, and important notes for configuration.
To Next Page
General