Lenze ESMD223L4TXA User Manual

22 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

Instructions de mise en service

FR

SMD

Frequency Inverter

0.37 kW... 22 kW

Betriebsanleitun

DE

Instrucciones de funcionamiento

IT

Istruzioni di funzionamento

ES

Operating Instructions

EN

(13466184)

Questions and Answers:

J
Jason ShawAug 29, 2025
Why is my Lenze Inverter showing overvoltage on DC bus?
- T
  Todd ArmstrongAug 29, 2025
  If your Lenze Inverter is experiencing an overvoltage on the DC bus, it could be due to several reasons: * The mains voltage might be too high: Verify the mains voltage. * The deceleration time might be excessively short, or the motor might be in generator mode: Increase the deceleration time or consider using a dynamic braking option. * Earth leakage on the motor side: Check the motor and motor cable, separating the motor from the controller to diagnose.
S
Scott WilliamsAug 29, 2025
What to do if Lenze ESMD223L4TXA Inverter shows short-circuit or overload?
- S
  Scott PhillipsAug 29, 2025
  If the Lenze Inverter experiences a short-circuit or overload, there are several potential causes: * A short-circuit itself: Investigate the cause and inspect the motor cable. * Excessive capacitive charging current: Use shorter motor cables. * Acceleration time is too short: Increase the acceleration time and check the controller selection. * Defective motor cable: Check the wiring. * Internal fault in the motor: Check the motor. * Frequent and long overload: Check controller selection.
N
Natalie RamirezAug 28, 2025
What to do if Lenze DC Drives have a communication error?
- A
  athompsonAug 28, 2025
  If Lenze DC Drives have a communication error, it may be because the serial timer has timed out. Check the serial link connections.
M
margaretlynchAug 27, 2025
What to do if Lenze DC Drives have a single phase fault?
- A
  April MckeeAug 27, 2025
  If Lenze DC Drives have a single phase fault, it means a mains phase has been lost. Check the mains voltage.
J
Joshua GibsonAug 27, 2025
How to resolve dynamic braking fault in Lenze DC Drives?
- F
  frank29Aug 27, 2025
  A dynamic braking fault in Lenze DC Drives typically means that the dynamic braking resistors are overheating. To resolve this, increase the deceleration time.
A
Angel HillAug 26, 2025
What to do if Lenze DC Drives show undervoltage on DC bus?
- T
  tyler42Aug 26, 2025
  If Lenze DC Drives show undervoltage on the DC bus, it could be because the mains voltage is too low. Check the mains voltage.
B
Bradley AndersenAug 25, 2025
What to do if Lenze DC Drives have controller overtemperature?
- J
  juliewilliamsAug 26, 2025
  If the controller has an overtemperature, it means the controller is too hot inside. To resolve this, reduce the controller load and improve cooling.
M
Ms. Erika LawrenceAug 25, 2025
Why Lenze DC Drives show earth fault?
- A
  allenstevenAug 25, 2025
  An earth fault in Lenze DC Drives can occur if a motor phase is grounded, so you should check the motor and motor cable. It can also be due to excessive capacitive charging current of the motor cable, in this case use shorter motor cables with lower charging current.

Lenze ESMD223L4TXA Specifications

General

Type	Inverter
Power Rating	2.2 kW
Input Frequency	50/60 Hz
Frequency	0-500 Hz
Protection Class	IP20
Input Voltage	380-480 V
Output Voltage	0-480 V AC
Control Method	vector control
Communication Interface	CANopen
Cooling Method	Air cooling

Summary

Safety Information

General Safety Precautions

General safety warnings, risks of injury, and required qualifications for personnel.

Technical Data Overview

Product Ratings and Specifications

Detailed power, voltage, and current ratings for different models.

Installation Procedures

Electrical Installation and Wiring

EMC requirements, fuses, and cable cross-section recommendations.

Control Terminal Functions

Detailed description of each control terminal's function and settings.

Commissioning Guide

Parameter Setting Process

Parameter Menu Overview (C00-C24)

Troubleshooting and Fault Diagnosis

Status, Causes, and Remedies

Error Codes and Solutions (cF-LF)

Detailed list of error codes, their causes, and corrective actions.

Error Codes and Solutions (OC1-SF)

Further error codes including short-circuit, earth fault, and overload.

Related product manuals

Lenze ESMD222L4TXA

Preview: Lenze ESMD371X2SFA

Lenze ESMD371X2SFA

Lenze ESMD751L4TXA

Lenze ESMD752L4TXA

Lenze ESMD302L4TXA

Lenze ESMD152L4TXA

Lenze ESMD113L4TXA

Lenze ESMD402L4TXA

Lenze ESMD751X2SFA

Lenze ESMD371L4TXA

Lenze ESMD153L4TXA

Lenze ESMD112L4TXA