Lightinthebox GS-G90E User Manual

Contents
目录
Preface]
Thank you for choosing the wireless alarm system product of our company.
Wireless alarm system adopts the most advanced digital sensing and
controlling technologies, it is the intelligent alarm control system containing burglar
alarm, fire alarm, fire fighting, gas leakage and SOS.
Wireless alarm system uses the most advanced multiple random selection
technology, it avoids the problems of interference and alarm missing which usually
exist in the similar systems. This system can be used widely in residence, shops,
villa, and small enterprise and so on.
For your safety, before installing and using, we suggest you read this manual
carefully.
Caution：To ensure that you can enjoy the impeccable warranty service, do not
open the host-housing to repair and renovation by yourself or we will not provide
free warranty service. All the losses and the adverse consequences it makes will be
assumed by users.
Please make safekeeping to the user manual for reference when it is
necessary.
[Function Introduction]
1. Touch screen keypad GSM alarm system
2. 8 Wired defense zones and 100 wireless defense zones.
3. At most 5 wireless remote control codes.
4. Touch keypad， Built-in clock.，LCD display. Operate easily.
5. Voice prompt for each operation.
6. SMS prompt automatically about low power of battery.
7. SMS prompt when AC power lost or recovered.
8. Built-in intercom horn, two way communication can be realized.
9. Built-in wireless transmitting module, could be coding with wireless siren.
10. Build-in wireless transmitter,can control 4 relay outputs with home
appliances,such as lights,garage door,television,curtain,etc.
11. 1 group timed Arm and timed Disarm function.
12. Can store 6 groups of phone numbers: when alarming, system will make
alarm call to these numbers automatically.
13. Can store 2 groups of SMS numbers: when alarming, system will send
alarming SMS to these numbers automatically.
14. Can store 2 alarm center telephones.
15. Inquire the status of alarm panel by SMS.
16. Delay alarming for each defense zone(0-99 seconds)
17. 10-second voice message recording can be played automatically when
alarming.
18. The host can be used as a hand-free phone. Users can make call by the
keypad for telephone fee inquiry and charging.
19. One-key-control function: Out Arm, Home Arm, Remote Arm.
20. Real-time, delay, 24 hours, bypass defense zones programming function.
21. Wireless coding: easy to add additional wireless accessories.
22. Remote control Arm, Disarm, Monitor, and Intercom by phone.
23. Event Log Query: host automatically records 40 pieces of all information
concerning arm, disarm and alarm events.
24. Multi-type of arm: Remote control arm, out arm, home arm, timed arm, arm
by phone.
25. Built-in AAA NI-MH rechargeable battery: make alarm when power off.

Lightinthebox GS-G90E Specifications

General

Brand	Lightinthebox
Model	GS-G90E
Category	Security System
Operating Frequency	433MHz
Remote Control	Yes
Wireless Sensor	Yes
Working Temperature	-10°C to 50°C
Installation	Wall Mounted

Summary

Preface

Function Introduction

Alarm Host Diagram

Function Setting

Initialization

Initializes the alarm system by inserting SIM card and powering on the host.

System setting

Configures system settings via keypad, with a default password and auto-exit after inactivity.

Exit Setting

Exits the current setting mode and returns to the main interface with a long beep.

Coding of Remote Controller Setting

Codes wireless remote controllers to the alarm host, supporting up to 5 controllers.

Remote Controller Deleting Setting

Deletes previously coded remote controllers from the alarm host system.

Coding of Wireless Detector Setting

Codes wireless detectors to specific defense zones (02-99) for alarm triggering.

Single Wireless Detector Deleting Setting

Deletes a specific wireless detector from a defense zone (02-99).

All Wireless Detector Deleting Setting

Deletes all previously coded wireless detectors from the alarm system.

Alarm Zone Type Setting

Sets the alarm zone type (0-3) to determine detector behavior during arm states.

Wireless Equipment Coding Setting

Codes wireless equipment using SC2262 standard, supporting 8 address bits.

Remote Controller Sound Prompt setting

Configures external siren prompt for arm/disarm actions triggered by remote control.

Siren Ring Time setting

Sets the duration (00-15 minutes) for the siren to ring when an alarm occurs.

Arm Time Delayed Setting

Sets a delay (00-99 seconds) for the host to arm after the Out Arm command.

Alarm Delayed Setting

Sets a delay (00-99 seconds) before the host triggers an alarm for a specific zone.

Telephone Dial-up Cycle Times Setting

Sets the number of times the system attempts to dial phone numbers during an alarm.

Remote Call Ringing Times Setting

Sets the number of rings before the host responds to remote calls.

Voice Recording message Setting

Allows recording a voice message for the alarm system, replayed during alarms.

Password Change Setting

Allows changing the user or administrator passwords for system access.

Keypad lock Setting

Enables or disables the keypad lock to prevent unauthorized password changes.

Turning Host Timed Arm/Disarm on/off

Enables or disables the timed arm and disarm functions for the alarm host.

Host Timed Arm /Disarm Setting

Sets specific times for automatic arming and disarming of the alarm host.

Host Reset Setting

Resets the main host to factory default, deleting telephone numbers but not accessories.

Host Historical Records Inquires Setting

Enables querying historical records of system events, with page navigation controls.

Host Historical Records Inquires Deleting Setting

Deletes all historical records stored within the alarm host system.

Arm/ Disarm SMS alert Setting

Configures whether the alarm panel sends SMS alerts to the user upon arming/disarming.

System Clock Setting

Sets the system clock by inputting year, month, date, hour, minute, and second.

SMS Phone Number Setting

Sets phone numbers for receiving SMS alerts, supporting two groups.

SMS Phone Number Delete Setting

Deletes SMS phone numbers from the alarm host's memory.

Alarm call Number Setting

Sets phone numbers for alarm calls, supporting up to six groups.

Alarm call Number Delete Setting

Deletes alarm call phone numbers from the host's memory.

Defense Zone name Setting

Assigns names or types (SOS, fire, gas leak, etc.) to defense zones (02-99).

Host GSM Signal Checking

Operation Instructions

Main Host Status

Details the four system status types: Arm, Home Arm, Disarm, and System Setup.

Remote Controller Operation

Explains how to use the remote controller for Arm, Disarm, and other functions.

Away Arm

Activates the system to guard the entire house when no one is present.

Home Arm

Activates the system to guard perimeter while people are home, disabling indoor detectors.

Disarm

Stops the alarm and returns the system to a non-warning state.

Answer Alarm Call

Handles incoming alarm calls, allowing remote control via phone keypad.

Remote control by making call to host

Allows remote control of the alarm system by calling the host number.

SOS

Triggers an immediate alarm for emergencies like illness, fire, or break-ins.

Alarm host used as hand-free phone

Utilizes the alarm system host as a hands-free telephone.

Maintenance

Guidelines for regular inspection and testing of the alarm system and detectors.

Technical Parameter

Sensor detection

Procedures for testing detector functionality and communication with the host.

Notices

Important warnings regarding product usage, safety, modification, and prohibited actions.