Lincoln C Series Owner's/Operator's Manual

Page Number - 5
Form 404031
Service, One Lincoln Way, St. Louis, MO 63120-1578, (314)
679-4200 for your nearest authorized service center.
When ordering replacement parts, list: part number, descrip
-
tion, model number and series number.
LIMITED WARRANTY
Lincoln warrants that lubrication equipment, materials dispens-
ing equipment and other related equipment manufactured by
it will be free from defects in material and workmanship during
the one (1) year following the date of purchase. If equipment
proves to be defective during this warranty period, it will be
repaired or replaced without charge, provided that factory
examination indicates the equipment to be defective. To
obtain repair or replacement, it must be shipped, transpor-
tation charges prepaid, with proof of date of purchase to
a Lincoln authorized Warranty and Service Center, within
the one (1) year following the date of purchase.
This warranty is extended to the original retail purchaser only.
This warranty does not apply to equipment damaged from ac-
cident, overload, abuse, misuse, negligence, faulty installation
or abrasive or corrosive materials, or to equipment repaired
or altered by anyone not authorized by Lincoln to repair or
alter the equipment. This warranty applies only to equipment
installed and operated according to the recommendations of
Lincoln or its authorized field personnel.
No other express warranty applies to lubrication equipment,
materials dispensing equipment, and other related
equipment manufactured by Lincoln. ANY IMPLIED WARRAN
-
TIES applicable to lubrication equipment, materials
dispensing equipment, and other related equipment manufac-
tured by Lincoln INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, WILL LAST ONLY FOR ONE (1) YEAR FROM
THE DATE OF PURCHASE. SOME STATES DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO
YOU.
In no event shall Lincoln be liable for incidental or consequen-
tial damages. The liability of Lincoln on any claim for loss or
damage arising out of the sale, resale, or use of lubrication
equipment, materials dispensing equipment, and other related
equipment shall in no event exceed the purchase price. SOME
STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION
OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE
ABOVE LIMITATION OR EXCLUSION MAY NOT APPLYTO
YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS
AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY
FROM STATE TO STATE.
ADJUSTMENT
See Figure (3). The guide arm may be positioned in 22-1/2
degree increments. For ease of operation and increased hose
life, the guide arm should be positioned to minimize hose
strain as the delivery hose is pulled through the roller outlet.
Three studs must be used to securely attach the guide arm, It
may be necessary to change the position of the hex head screw
and one stud in order to obtain the desired guide arm position.
The hose clamp must be relocated if the guide arm is reposi
-
tioned.
SAFETY INFORMATION
Read and understand all warnings, cautions and instructions
before operating this equipment. Extreme caution should be
used when operating this equipment as personal injury and/or
property damage can result from equipment misuse. Adequate
personal protection is recommended to prevent splashing of
material on the skin or in the eyes. ALWAYS disconnect air
coupler from pump when the pump is not being used.
PRESSURE RELIEF PROCEDURE
Always perform this procedure when the pump is shut off
and before checking, servicing, installing, cleaning or repairing
any part of this system.
Perform the following procedure:
A. Disconnect the air supply to
the pump.
B. Point the dispensing valve away from yourself and others.
C. Open the dispensing valve into an appropriate container
until the pressure is relieved.
If the above procedure does not relieve the pressure, the
dispensing valve or hose may be restricted
To relieve the pressure, very slowly loosen the hose end cou
-
pling. Then loosen completely and clear the dispensing valve
and/or hose.
INSPECTION
Prior to operation or maintenance a visual inspection shall be
made. Check reelsystem for leaks, worn or missing parts.
Any reel that appears to be damaged in any way, is badly
worn or operates abnormally shall be removed from use until
repairs are made. Contact factory authorized service center for
repairs.
If overpressurizing of the equipment is believed to have oc-
curred, contact a factory authorized service center for inspec-
tion of the reel.
Annual inspection by a factory authorized service center is
recommended.
DISASSEMBLY
To disassemble, perform ASSEMBLY procedures in reverse.
REPAIR
Repair is limited to replacement of listed service parts. Special
procedures and tools are required. Contact LincolnCustomer
To order call 1-800-548-1191 or visit www.partdeal.com - info@partdeal.com

Lincoln C Series Specifications

General

Brand	Lincoln
Model	C Series
Category	Measuring Instruments
Language	English