Lincoln C Series User Manual (English)

Other manuals for Lincoln C Series

Manual24 pages

Owner's Manual6 pages

Owner's/Operator's Manual8 pages

Quick Start Guide8 pages

Questions and Answers:

A
Adam WhiteAug 14, 2025
Why Lincoln Water Pump motor does not run?
- S
  Steven WilliamsAug 14, 2025
  If the Lincoln Water Pump motor isn't running, it could be due to a few reasons. First, check the voltage supply to the pump; an interruption here could be the problem, so eliminate the cause of the fault. Second, the voltage supply to the printed-circuit board might be interrupted; inspect the line from the pump plug to the printed circuit board. Lastly, the printed circuit board itself may be defective, requiring replacement.
H
Heather MeyerAug 17, 2025
Why is Lincoln Measuring Instruments meter inaccurate?
- C
  Christine DavisAug 18, 2025
  If the Lincoln Measuring Instruments are inaccurate, the scale factor may not be correct for the fluid you're measuring. To resolve this, enter program mode and check and reset the program factor.
J
Jennifer GordonAug 21, 2025
What to do if Lincoln Measuring Instruments have slow or no fluid flow?
- C
  Christine BooneAug 21, 2025
  If you're experiencing slow or no fluid flow with your Lincoln Measuring Instruments, several factors could be responsible. The filter in the swivel nut might be clogged, so clean or replace it. Alternatively, the pump pressure could be low; try increasing the pump pressure. If these steps don't resolve the issue, foreign material may be jamming the meter.
J
jonesanthonyAug 25, 2025
What to do if the Lincoln Water Pump motor runs permanently for 30 minutes?
- M
  miranda39Aug 25, 2025
  If the Lincoln Water Pump motor runs continuously for 30 minutes, the issue might stem from a defective proximity switch. Try disconnecting the main line to the monitored metering device. Alternatively, the cable connection of the proximity switch to the pump could be interrupted; in this case, check the cable connections to the pump, and if needed, replace the proximity switch with the connector. As a last resort, the printed circuit board might be defective, requiring replacement.
K
Kiara BlakeAug 27, 2025
What to do if there is excessive air or fluid from the air exhaust in Lincoln Engine?
- K
  Kyle BerryAug 27, 2025
  If you observe an excessive amount of air in the fluid or too much fluid coming from the air exhaust of your Lincoln Engine (note that some fluid exhaust is normal), you should replace the 34310 Packing, 35135 Gland Packing, and 31050 Gland Gasket.
F
Frank SheaAug 30, 2025
What to do if Lincoln Engine pump does not operate?
- T
  Thomas AlexanderAug 31, 2025
  If the Lincoln Engine pump does not operate, check the air supply to the air motor. Also, replace the 11475 Trip Shoe Assembly, 11947 Trip Sleeve, and 91331 Toggle Plate.
K
Kimberly PachecoSep 3, 2025
What to do if Lincoln Measuring Instruments meter does not latch for batching?
- P
  Paul GarciaSep 3, 2025
  If the Lincoln Measuring Instruments meter does not latch for batching, it might be due to several reasons. First, ensure the meter is in AUTO mode by pressing the AUTO button and programming the batch size. Second, the meter may not have been reset after the prior batch, so press the RESET button. Finally, low batteries can cause this issue; check for the battery icon, replace the batteries, and then push the RESET button.
A
Andre TrujilloSep 6, 2025
What to do if Lincoln Measuring Instruments display is blank?
- J
  Julia CarterSep 6, 2025
  If the display of your Lincoln Measuring Instruments is blank, the meter may be asleep; try pushing the reset button. Alternatively, the batteries might be dead; replace them and push the reset button. A program error could also cause this; remove and reinsert the battery pack, then push the reset button. Lastly, a loose battery connection could be the culprit; remove the battery pack, check the connection, and push the reset button.
J
Johnny BrownSep 9, 2025
How to fix battery icon on Lincoln Measuring Instruments?
- J
  Judy WhiteSep 9, 2025
  If your Lincoln Measuring Instruments show the battery icon, it means the batteries are low and need to be replaced.