EasyManua.ls Logo

Linde E 25-02 - User Manual

Linde E 25-02
96 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
With Electric Motors
336 804 3001 GB
E 20 - 02 / E 25 - 02 / E 30 - 02
E 20/600 - 02 / E 25/600 - 02 / E 30/600 - 02
Operating Instructions
0704
Linde Fork Lift Truck
e336-02/01

Table of Contents

Questions and Answers

  • A
    Andrea FlowersAug 10, 2025
    What to do if my Linde Forklifts truck does not start?
    • G
      Gregory WilsonAug 10, 2025
      If your Linde Forklifts truck doesn't start, several issues could be the cause. First, check if the battery is discharged and charge or replace it if necessary. Ensure all electrical connections are tight, especially at the battery terminals, and coat them with non-acidic grease. Verify that the overhead guard is correctly locked. Finally, inspect the fuses and replace any that are blown.
  • K
    Kelly BassAug 17, 2025
    How to troubleshoot abnormal noise in Linde E 25-02 Forklifts?
    • H
      Holly RiddleAug 17, 2025
      Abnormal noise in your Linde Forklifts can stem from several causes. Start by checking the suction filter for restrictions and clean or replace it. Inspect suction hoses for leaks, and if oil foams, tighten the hose connections. If these steps don't resolve the issue, the hydraulic pump may be damaged, or seals may be faulty, leading to air intake, in which case you should have it inspected by your authorised distributor. Also, ensure you're using the correct oil viscosity and that the oil level in the tank is adequate; change the oil and replenish if needed.
  • C
    Catherine PollardAug 25, 2025
    Why is there no or too low pressure in the Linde E 25-02 system?
    • U
      uparkerAug 25, 2025
      If you're experiencing no or low pressure in your Linde Forklifts system, several factors could be responsible. Check for pump suction faults, which may be noisy, and change or replenish the oil. Pump failure, pressure valve issues (such as valves not closing or valve seat damage) can also be the cause, and you should have it repaired by distributor’s mechanic. Inspect the pipeline for breaks or leaks, replacing the pipe or tightening connections as necessary. Also, using oil with low viscosity can lead to high leakage losses, so change the oil and use the specified viscosity.
  • M
    Matthew DavisSep 1, 2025
    What causes the hydraulic oil temperature to be too high in Linde E 25-02?
    • S
      Scott MarshallSep 1, 2025
      High hydraulic oil temperature in your Linde Forklifts can be caused by pump failure or leaking valves, in which case you should have it repaired by a workshop. Also, check the oil level and replenish if it is too low.

Summary

Truck Description & Specifications

Technical description

Overview of truck systems: drive, steering, hydraulics, brakes, electrical.

Controls and indicators

Identification of dashboard controls and indicators.

Composite instrument

Details on the instrument cluster, hour meter, and battery indicator.

Operation & Safety

Safety rules

General safety guidelines and precautions for truck operation.

Daily checks

Routine checks to be performed daily before operation.

Battery charging and checks

Instructions for charging, checking battery level and condition.

Seat belt procedures

Proper procedure for fastening, opening, and checking the seat belt.

Emergency isolator button operation

Instructions for pushing and pulling the emergency stop button.

Driving operations

How to drive forward, reverse, change direction, and use joystick/single controls.

Steering system operation

Details on the hydrostatic steering system and turning radii.

Braking system overview

Description of service, regenerative, foot, and electric motor brakes.

Truck Data Management (LFM)

Overview of LFM system, login, startup, and component access.

Wheel change procedure

Instructions for changing front and rear wheels, including jack locations.

Manual mast tilting and fork lowering

Procedures for manual mast tilt and fork lowering in case of malfunction.

Emergency exit procedures

How to exit the truck through the rear window in emergencies.

Maintenance

Maintenance intervals

Guidelines for scheduled maintenance based on hours and conditions.

Seat belt inspection and operation

Regular checks for seat belt condition and proper function.

Renewing carbon brushes and wheel nuts

Instructions for replacing motor brushes and tightening wheel nuts.

Braking system checks

Checking the handbrake, brake pedal, linings, and discs.

Motor brush inspection

Visual check of motor brushes for condition and length.

Mast, lift chain, and end stop checks

Hydraulic oil level check

Filter renewal

Renewing the hydraulic oil

Changing wheel drive oil (3000 hr)

Inspection and maintenance specifications

Lubricant recommendations

Troubleshooting guide

Guide to diagnosing and resolving common truck problems.

Linde E 25-02 Specifications

General IconGeneral
BrandLinde
ModelE 25-02
CategoryForklifts
LanguageEnglish

Related product manuals