Linksys SPA1001

5-20
Linksys IP Phone Administrator Guide
Document Version 3.2
Chapter 5 Linksys ATA Field Reference
Regional Tab
Ring Back Tone Played during an outbound call when the far end is ringing.
The default is 440@-19,480@-19;*(2/4/1+2).
Confirm Tone Brief tone to notify the user that the last input value has been accepted.
The default is 600@-16; 1(.25/.25/1).
SIT1 Tone Alternative to the Reorder Tone played when an error occurs as a caller makes an
outbound call. The RSC to trigger this tone is configurable on the SIP screen.
The default is 985@-16,1428@-16,1777@-16;20(.380/0/1,.380/0/2,.380/0/3,0/4/0).
SIT2 Tone Alternative to the Reorder Tone played when an error occurs as a caller makes an
outbound call. The RSC to trigger this tone is configurable on the SIP screen.
The default is 914@-16,1371@-16,1777@-16;20(.274/0/1,.274/0/2,.380/0/3,0/4/0).
SIT3 Tone Alternative to the Reorder Tone played when an error occurs as a caller makes an
outbound call. The RSC to trigger this tone is configurable on the SIP screen.
The default is 914@-16,1371@-16,1777@-16;20(.380/0/1,.380/0/2,.380/0/3,0/4/0)
SIT4 Tone This is an alternative to the Reorder Tone played when an error occurs as a caller makes
an outbound call. The RSC to trigger this tone is configurable on the SIP screen.
The default is 985@-16,1371@-16,1777@-16;20(.380/0/1,.274/0/2,.380/0/3,0/4/0).
MWI Dial Tone Played instead of the Dial Tone when there are unheard messages in the caller’s mailbox.
The default is 350@-19,440@-19;2(.1/.1/1+2);10(*/0/1+2).
Cfwd Dial Tone Played when all calls are forwarded.
The default is 350@-19,440@-19;2(.2/.2/1+2);10(*/0/1+2).
Holding Tone Informs the local caller that the far end has placed the call on hold.
The default is 600@-19*(.1/.1/1,.1/.1/1,.1/9.5/1).
Conference Tone Played to all parties when a three-way conference call is in progress.
The default is 350@-19;20(.1/.1/1,.1/9.7/1).
Secure Call Indication Tone Played when a call has been successfully switched to secure mode. It should be played
only for a short while (less than 30 seconds) and at a reduced level (less than -19 dBm) so
it does not interfere with the conversation.
The default is 397@-19,507@-19;15(0/2/0,.2/.1/1,.1/2.1/2).
VoIP PIN Tone Specification of the tone played to prompt a VoIP caller for a PIN number (if PIN
authentication is selected and the caller requires authentication to use the PSTN gateway).
The default is 600@-10;*(0/1/1,.1/.1/1,.1/.1/1,.1/.5/1)
PSTN PIN Tone Specification of the tone played to prompt a PSTN caller for a PIN number (if PIN
authentication is selected and the caller requires authentication to use the VoIP gateway).
The default is 600@-10;*(0/.7/1,.2/.1/1,.2/.1/1,.2/.5/1).
Feature Invocation Tone Played when a feature is implemented. (Not in PAP2T)
The default is 350@-16;*(.1/.1/1).