LogTag UTRIX-16 - Manufacturing Phase 1: PCBA Assembly and Mounting; Component Integration; PCBA Testing and Programming; Case Assembly and Protection

LogTag’s UTRIX-16(M) is a fully configurable,multi-use USB PDF
temperature recorder that can create temperature reports without
the need to install proprietary software or hardware at the
destination. The recorder can be ordered with pre-set profiles ready
to start, or configured using LogTag
®
Analyzer, and is then placed
with the goods to be monitored. At the destination the UTRID-16 can
be plugged straight into a computer’s USB port and generates a PDF
file, which can be accessed using PDF software such as Acrobat
Reader.
Checklist - Required Equipment
l LogTag
®
UTRIX-16(M) temperature recorder. It is recommended
that you connect each USB PDF Temperature Recorder via a
permanently plugged in USB extension cable to protect your
computer’s USB socket.
l A computer running Windows XP or later, Mac OSX or Linux.
l For configuration - a PC running Windows XP SP3 or later and
LogTag
®
Analyzer installed.
Features
The UTRIX-16(M) USB PDF temperature recorder features the
familiar LogTag case layout with an additional USB plug at the
bottom.
Case
l Mounting lug for secure fastening of recorder to fixtures
l USB plug with potective cap - shields USB connector from
moisture and dirt
l Temperature sensor located inside case
l Durable polycarbonate case, IP64
Buttons
l
START/Mark button; can be used to start the unit or place an
inspection mark in the data listing
l
STOP button; can be used to stop the unit.
Indicator LEDs
l
Green OK indicator
Blinks if the unit is operating without alerts being present.
l
Red ALERT indicator
Blinks if an alarm condition has occurred during the trip.
Software Requirements
Software requirements vary depending on the type of file you want
the UTRIX-16(M) to generate when plugged into a USB port.
l If you wish to configure UTRIX-16(M) products you will need to
download the LogTag
®
Analyzer software from LogTag
®
’s web
site at http://www.logtagrecorders.com/software/download.php.
Follow the instruction to install and start the software.
l
If you only plan on evaluating data, plug the UTRIX-16(M) into a
computer‘s USB socket. Depending on the settings made during
configuration, a number of files will be generated
1
and made
available to you in a new drive:
o
A PDF file; you can open the file directly from the recorder‘s
USB memory storage with Acrobat Reader 4.0 or later, or any
other compatible PDF reader software of your choice.
o
A CSV file; this file can be imported into a spreadsheet
program such as Microsoft Excel.
o
An LTD file; LTD files are LogTag
®
Analyzer's native,
encrypted data files. You can open this file in LogTag
®
Analyzer, where you can analyze data in detail and generate
report files. Here, you can also combine charts from multiple
recorders for comparison.
l You can also download data directly into LogTag
®
Analyzer
without accessing the recorder‘s USB memory storage.
Configuring the UTRIX-16(M)
UTRIX-16(M) products can be ordered pre-configured, ready to start.
Different profiles are available; if none of these suit or the UTRIX-16
(M) needs different configuration settings to those already installed,
the unit can be configured using LogTag
®
Analyzer.
l
Start the LogTag
®
Analyzer software.
l
Remove the protective cap and insert the UTRIX-16(M) into a
USB port. You will receive a message that a new USB device has
been found, and a generic driver will be installed
2
.
l
Once the driver is installed and the UTRIX-16(M) is ready (shown
by the green OK indicator blinking), it can receive configuration
1
Depending on the configuration, the UTRIX-16(M) may produce all, some or none
of the files.
2
Depending on the factory configuration additional drivers may be installed at this
time.
Page 5 of 16 UTRIX-16(M) Product User Guide, Revision 2.0, copyright © 2004-2016, LogTag
®
Recorders . All rights reserved.
Introduction