Why the ONVIF software cannot find Lumens VC-TR40NB Security Camera?
If the ONVIF software is unable to locate your Lumens Security Camera, ensure that the [Camera ID] and [Location] fields under [System] > [Output] in the web page settings contain only English letters or numbers. Special characters and spaces in these fields can prevent the software from detecting the camera.
What to do if Lumens VC-TR40NB Security Camera image is severely delayed?
To resolve the issue of a severely delayed image from your Lumens Security Camera, switch to using 1080p or 720p at 60/50 fps instead of 25/30 fps signals.
Why Lumens VC-TR40NB Security Camera does not save parameters after reboot?
If your Lumens Security Camera fails to save parameters like PTZ or AWB after a reboot, check whether the Initial Position is set to Last MEM. You can find this setting in the Setting Menu under System - Initial Position, or on the web page under Live View-Setting–Camera Setting - PTZ - Initial Position.
What to do if there is no image output from Lumens VC-TR40NB?
If your Lumens Security Camera is not providing an image output, verify the following: * Check the power supply or PoE supply functions. * Confirm the output signals are in streaming output. * Ensure the camera resolution is compatible with the monitor equipment. * Replace the cables to rule out any faults.
How to fix RS-232 control issues with Lumens Security Camera?
If the RS-232 cannot be controlled on your Lumens Security Camera, please check the following: 1. Confirm the connection is correct (RS-232 In/ Out). 2. Ensure the Baud rate setting is the same as the control equipment.
How to troubleshoot Lumens Security Camera that won't boot?
If your Lumens Security Camera does not boot and shows no power signal: 1. Ensure the power cord is properly plugged in. 2. If using a PoE connection, verify that the power supply supports PoE (IEEE802.3af) hubs.
Why Lumens VC-TR40NB VC-TR40 cannot be operated by remote control?
If you're having trouble operating your Lumens VC-TR40 Security Camera with the remote control, consider the following: Ensure the IR Select setting in the camera menu matches the Camera Select setting on the remote. Try replacing the remote's batteries. Prevent direct sunlight from shining on the VC-TR40. Keep energy-saving bulbs and IR touch screens as far away as possible to avoid interference. If multiple VC-TR40 cameras are in the same area, operating two remote controls simultaneously may cause signal interference; use only one remote control at a time.
How to fix ONVIF software cannot find Lumens VC-TR40NB Security Camera?
If the ONVIF software is unable to find your Lumens Security Camera, ensure that the [Setting] > [Video] > [Camera ID] / [Location] fields in the web page use only English letters or numbers. The ONVIF software cannot find the machine if you use special characters and space.
How to fix Lumens Security Camera RS-232 cannot be controlled?
If the RS-232 control isn't working for your Lumens Security Camera, first confirm that the connection is correct (RS-232 In/ Out). Also, make sure the Baud rate setting is the same as that of the control equipment.
How to fix Lumens VC-TR40NB Security Camera boot without power signal?
If your Lumens Security Camera doesn't boot and shows no power signal, ensure that the power cord is properly plugged in. When using a PoE connection, verify that the power supply supports PoE (IEEE802.3af) hubs.
General| Image Sensor | 1/2.8" CMOS |
|---|---|
| Video Output | HDMI |
| Audio Input | Line in |
| IP Streaming | H.264, MJPEG |
| Control Interface | RS-232 |
| Effective Pixels | 2.07MP |
| Lens | f=4.7~mm |
| Day/Night | Yes |
| Video Compression | H.264, MJPEG |
| Network Interface | 10/100/1000 Base-T |
| Power Supply | DC12V, PoE |
To Next Page
