MacAllister MCS2400 - User Manual

Original Instructions_MNL_MCS2400_GB_V05_111108
MCS2400
2400W Electric
Chain Saw
Barcode: 5052931013890
MNL_MCS2400_DFT_GB_V05_111108.indd 1 11/8/11 5:17:13 PM

Summary

Before you start

Unpack

Instructions for unpacking the chainsaw, checking contents and preparing for assembly and operation.

Assembly

Chain and guide bar

Detailed steps for attaching the chain and guide bar to the chainsaw.

Chain brake warning

Crucial safety warning regarding the use of low-kickback chains and chain brake functionality.

Aligning guide bar and chain

Instructions on aligning the guide bar and saw chain with the drive sprocket.

Replacing the cover and initial tensioning

Steps for replacing the cover and initial saw chain tensioning.

Chain tensioning warnings

Critical safety warnings about chain tensioning, kickback risk, and chain life.

Checking and adjusting chain tension

Procedure for checking and adjusting the saw chain tension to the correct level.

Securing the cover

Instructions for fully tightening the cover after chain tensioning.

Lubrication

Lubrication warnings

Critical warnings about operating the chainsaw without oil and its consequences.

Filling the oil tank

Step-by-step guide to filling the oil tank using the correct oil type.

Checking oil level

How to check the oil level using the oil level window and when to refill.

Disposal of used lubricant

Guidance on the proper disposal of lubricant and contaminated items.

Connection to the power supply

Power connection warnings

Safety warnings regarding extension cable type, RCD use, and voltage checks.

Connecting extension cable

Procedure for attaching the extension cable to the chainsaw's strain relief.

Safety

General safety checklist

A comprehensive checklist of safety items to confirm before using the product.

Product functions

Intended use

Defines the purpose and limitations of the electric chain saw.

Overload protection

Explanation of the overload protection mechanism and how to reset the circuit breaker.

Chain brake

Description of the chain brake mechanism and its function.

Chain brake test

Procedure for testing the chain brake's functionality before each use.

Chain brake operation

How to engage and disengage the chain brake using the lock-off button and switch.

On;off switch

Instructions on how to operate the power switch and lock-off button.

Operation

General operation

Pre-operation checks, safe handling, and working practices for the chainsaw.

Basic operating; cutting procedure

Steps for holding the product, positioning, and making cuts safely.

Cutting procedure with spike bumper

Using the spike bumper for leverage and securing the saw during cutting.

Cutting safety guidelines

Precautions for arm extension, cutting height, and handling the weight shift.

Kickback explanation

Explanation of kickback causes like tip contact and pinching, with visual examples.

Kickback reactions

Description of how the chainsaw reacts during kickback incidents.

Kickback prevention

Tips and best practices to avoid kickback, including grip and chain maintenance.

Felling a tree

Safety considerations and procedures for felling trees, including spacing and terrain.

Felling escape path

Planning and clearing an escape path before starting tree felling operations.

Notching undercut

Procedure for making the notching undercut for felling a tree.

Felling back cut

Steps for making the felling back cut, including hinge wood and wedge use.

Limbing and pruning

Techniques for removing branches from a fallen tree and safety warnings.

Limbing safety warnings

Safety warnings about climbing, ladder use, and flush cuts during pruning.

Cutting spring poles

Identification and caution regarding spring poles, logs bent under tension.

Bucking a log - Supported log

Cutting a log into lengths when supported along its entire length.

Bucking a log - Single end support

Procedure for bucking logs supported on one end.

Bucking a log - Double end support

Steps for bucking logs supported on both ends.

Bucking on a slope

Safety and technique for bucking logs on a slope.

Bucking small logs

Methods for supporting small logs on a sawing stand or another log.

Bucking large logs with wedge

Using a wedge to hold large logs open and prevent pinching.

After use

Product after use procedures

Procedures for switching off, cooling down, and storing the chainsaw after operation.

Care and maintenance

Golden rules for care

Key principles for product care, cleaning, inspection, and repairs.

General cleaning

How to clean the chainsaw using a dry cloth, brush, or compressed air.

Cleaning warnings

Warnings against using chemical or abrasive cleaning agents on the product.

Sprocket nose lubrication

Procedure for lubricating the sprocket nose using a disposable lube gun.

Guide bar and saw chain maintenance

Tips to prevent guide bar problems and maintain the guide bar and chain.

Oiling port cleaning

How to clean the oiling port for proper lubrication of the guide bar and chain.

Oiling system check

Checking the oil passages and automatic oiling system functionality.

Drive sprocket inspection

Checking the drive sprocket for wear or damage and replacement.

Guide bar rail inspection and maintenance

How to check the guide bar rail for wear and turn the guide bar for even wear.

Saw chain maintenance

Checking the saw chain for wear, sharpening, or replacement.

Saw chain sharpening

Instructions on sharpening the saw chain yourself or professionally.

Sharpening warnings

Safety warnings about sharpening the saw chain only if trained and experienced.

Power cord replacement

Instructions and warnings for replacing the power cord and UK plug.

UK plug wiring

Wiring instructions for the UK plug, identifying live and neutral terminals.

Plug replacement warnings

Warnings against connecting wrong wires to terminals and using approved plugs/fuses.

Repair

User repair limitations

Information that the product contains no user-repairable parts; contact a specialist.

Storage

Product storage guidelines

Guidelines for cleaning, storing, and protecting the chainsaw.

Transportation

Safe transportation procedures

Instructions for safely transporting the chainsaw, including disconnecting and securing.

Trouble shooting

Product does not start

Troubleshooting steps for when the product fails to start.

Product does not reach full power

Solutions for issues where the product is not operating at full power.

Unsatisfactory cutting performance

Causes and solutions for poor cutting performance, like chain tension or bluntness.

Recycling and disposal

Waste electrical and oily item disposal

Information on proper disposal of electrical waste and oily items.

Technical specifications

General specifications

Key technical details such as voltage, power, cutting length, and oil capacity.

Sound level specifications

Measured and guaranteed sound power and pressure levels according to standards.

Hand arm vibration specifications

Vibration levels for front and rear handles, and uncertainty factor.

Vibration warning

Warning about actual vibration values differing from declared and measures for protection.

Symbols and abbreviations

Explanation of symbols and abbreviations used on the product and in the manual.

Technical and legal information

Safety precautions

Visual guide to safety precautions including wearing protective equipment and handling warnings.

Handling warnings

Warnings related to switching off, removing plugs, tip contact, and two-handed operation.

General safety symbols

Explanation of symbols for chain brake, rain exposure, and thrown objects.

Product symbols

Explanation of symbols for sound power level, protection class, CE mark, and WEEE.

General power tool safety warnings

General warnings applicable to all power tools, emphasizing reading instructions.

Work area safety

Guidelines for maintaining a safe work area, avoiding hazards, and keeping others clear.

Electrical safety

Precautions for safe electrical connections, avoiding water, and cord care.

Personal safety

Advice on staying alert, using common sense, and wearing personal protective equipment.

Safety warnings

Warnings about unintentional starting, removing keys, overreaching, and dress code.

Power tool use and care

Guidelines for not forcing the tool, checking the switch, and disconnecting for adjustments.

Tool maintenance and sharp cutting tools

Importance of maintaining power tools, keeping cutting tools sharp and clean.

Service and chain saw safety

Advice on servicing, holding the saw, protective equipment, and avoiding tree operation.

Chain saw operation safety

Safety points for holding the saw, protective gear, and operating on stable surfaces.

Safety warnings - Spring back and brush cutting

Warnings for cutting under tension, brush, saplings, and keeping handles dry.

Causes and operator prevention of kickback

Detailed explanation of kickback causes and operator actions to prevent it.

Kickback control and replacement parts

Tips for controlling kickback forces, using specified parts, and sharpening.

Clothing and protective equipment

List of required and recommended safety clothing and protective equipment.

Vibration and noise reduction

Measures to reduce impact of noise and vibration, including operating time and PPE.

Emergency procedures

What to do in case of malfunction, and the importance of early intervention.

Residual risks

Potential risks remaining even with safety requirements, like health defects from vibration.

Property damage risks

Risks of injury and damage from broken tools, hidden objects, or thrown items.

Vibration exposure and medical implants

Risks of prolonged vibration exposure and electromagnetic field interference with medical implants.

Guarantee

Guarantee terms and conditions

Information on the 24-month guarantee period, replacement policy, and non-covered defects.

Fault reporting helpline

Contact information for reporting product faults and statutory rights.

EC declaration of conformity

Product compliance statement

Statement of compliance with Machinery, Low Voltage, EMC, and Noise Directives.

Technical standards and notified body

List of referenced technical standards and details of the notified body.

MacAllister MCS2400 Specifications

General

Power	2400 W
Bar length	45 cm
Chain speed	14 m/s
Weight	5.4 kg
Cable length	0.35 m
Oil tank volume	0.2 L
Power Source	Electric
Voltage	240 V