Need help?Do you have a question about the Magic-Pro Computer MP-6VIP-C+ and is the answer not in the manual?
Details FCC compliance rules and conditions for device operation.
Statement regarding audio noise emissions limits for digital apparatus.
Legal disclaimer concerning content accuracy, liability, and copyright.
Details supported Intel and Cyrix CPUs, bus speeds, and multipliers.
Specifies the VIA APOLLO PRO133 VT82C693A chipset.
Describes DIMM sockets and the supported DRAM size range.
Lists the available AGP, PCI, and ISA slots.
Details IDE, USB, PS/2, Floppy, and UART ports.
Mentions ATX power connector and power-on by LAN, RTC, or Modem.
Specifies the presence of 2MB FLASH BIOS with AWARD BIOS support.
Describes the ATX form factor and PCB dimensions.
Visual layout of motherboard components, connectors, and jumpers.
Explains the function of pins for J2 and J3 jumpers.
Describes the function of FAN1, FAN2, and FAN3 connectors.
Configuration settings for enabling keyboard power-on functionality.
Settings for controlling the signal level shift.
Configures the CPU host clock speed using JP4 and JP5 jumpers.
Configures the bus clock speed using the JP6 jumper.
Selects USB port redirection using JP10 and JP11 jumpers.
Sets VGA usage for PCI or AGP cards via the JVGA1 jumper.
Controls system power resume behavior after power loss.
Selects between Intel and Cyrix CPUs using JP20, JP21, JP22 jumpers.
Instructions for clearing CMOS memory using the JBAT1 jumper.
Configures the CPU bus ratio using JP12, JP13, JP14, and JP15 jumpers.
Description of the Wake On LAN connector and operational requirements.
Instructions for accessing and navigating the BIOS setup utility.
Overview of the main menu options available in the BIOS setup.
Configuration of basic hardware settings like date, time, and drives.
Procedure for setting the system's current date and time.
Configuration for IDE hard disks and floppy disk drives.
Settings for video display type and system halt conditions.
Setup for optimizing system performance and configuring BIOS features.
Configuration for virus protection and CPU cache settings.
Settings for boot sequence and floppy drive seek behavior.
Options for floppy seek, NumLock status, and HDD block mode.
Settings for Gate A20, memory parity, typematic rate, and security.
Settings for PCI/VGA palette snooping and DRAM configuration.
Configuration for mapping VGA BIOS to system RAM.
Adjusts chipset registers to control system options.
Configures DRAM timings and CAS latency cycle length.
Settings for DRAM clock and reserving memory for ISA cards.
Settings for Read Around Write and Concurrent PCI/Host modes.
Settings for video RAM caching and AGP aperture size/mode.
Configuration for onboard USB functionality and keyboard support.
Configures system power saving functions and behaviors.
Settings for ACPI, general power management, and APM control.
Options for video off, video off method, and modem IRQ settings.
Settings for power button behavior, HDD power down, and sleep modes.
Controls wake-up behavior for VGA, LPT/COM, HDD/FDD, and DMA.
Settings for modem ring, wake-on-LAN, and RTC alarm wake-up.
Lists IRQs that can be exempted from power management.
Defines PCI bus slots and Plug and Play configuration.
Settings for OS support of PnP and resource control.
Configuration for PCI write buffers, bursting, and transactions.
Settings for AGP master write and read operations.
Assigns an IRQ to the USB controller.
Assigns an IRQ to the VGA controller.
Loads default system values into configuration fields.
Allows adjustment of CPU settings and retention of information.
Sets the CPU ratio and host clock speed.
Settings for DIMM/PCI clock detection and spread spectrum.
Configures integrated chipset registers and system options.
Configuration for onboard IDE channels and prefetch mode.
Settings for PIO, UDMA modes, and initial display device.
Settings for KBC input clock and FDC controller.
Settings for serial ports, UART modes, and transmission delay.
Settings for parallel port mode, DMA, and EPP selection.
Configuration for keyboard power-on password and hot keys.
Allows setting system passwords for supervisor and user.
Note on clearing CMOS to reset lost passwords.
Detects IDE hard disk parameters for Standard CMOS Setup.
Saves configuration changes to CMOS and exits BIOS.
Exits BIOS setup without saving any modifications.
Step-by-step instructions for updating the BIOS flash memory.
Guide for installing motherboard drivers, especially for Windows 98 SE.
Explanation of the thermal sensor connector and VIA Hardware Monitor setup.
General| Brand | Magic-Pro Computer |
|---|---|
| Model | MP-6VIP-C+ |
| Category | Motherboard |
| Language | English |
To Next Page