Makita DDF485RTJ User Manual

4 ENGLISH
ENGLISH (Original instructions)
SPECIFICATIONS
Model: DDF485
Drilling capacities Steel 13 mm
Wood 38 mm
Fastening capacities Wood screw 6 mm x 75 mm
Machine screw M6
No load speed High (2) 0 - 1,900 min
-1
Low (1) 0 - 500 min
-1
Overall length 169 mm
Rated voltage D.C. 18 V
Net weight 1.4 - 1.7 kg
• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange
without notice.
• Specicationsmaydifferfromcountrytocountry.
• Theweightmaydifferdependingontheattachment(s),includingthebatterycartridge.Thelightestandheavi-
estcombination,accordingtoEPTA-Procedure01/2014,areshowninthetable.
Applicable battery cartridge
BL1815N/BL1820/BL1820B/BL1830/BL1830B/BL1840/BL1840B/BL1850/BL1850B/BL1860B
• Someofthebatterycartridgeslistedabovemaynotbeavailabledependingonyourregionofresidence.
WARNING: Only use the battery cartridges listed above.Useofanyotherbatterycartridgesmaycause
injuryand/orre.
Intended use
The tool is intended for drilling and screw driving in
wood, metal and plastic.
Noise
ThetypicalA-weightednoiseleveldeterminedaccord-
ingtoEN60745-2-1:
Sound pressure level (L
pA
):74dB(A)
Uncertainty(K):3dB(A)
Thenoiselevelunderworkingmayexceed80dB(A).
WARNING: Wear ear protection.
Vibration
Thevibrationtotalvalue(tri-axialvectorsum)deter-
minedaccordingtoEN60745-2-1:
Workmode:drillingintometal
Vibrationemission(a
h,D
):2.5m/s
2
or less
Uncertainty(K):1.5m/s
2
NOTE:Thedeclaredvibrationemissionvaluehas
beenmeasuredinaccordancewiththestandardtest
methodandmaybeusedforcomparingonetoolwith
another.
NOTE:Thedeclaredvibrationemissionvalue
mayalsobeusedinapreliminaryassessmentof
exposure.
WARNING:Thevibrationemissionduringactual
use of the power tool can differ from the declared
emissionvaluedependingonthewaysinwhichthe
tool is used.
WARNING:Besuretoidentifysafetymeasures
toprotecttheoperatorthatarebasedonanestima-
tion of exposure in the actual conditions of use (taking
accountofallpartsoftheoperatingcyclesuchas
the times when the tool is switched off and when it is
running idle in addition to the trigger time).
EC Declaration of Conformity
For European countries only
TheECdeclarationofconformityisincludedasAnnexA
to this instruction manual.
SAFETY WARNINGS
General power tool safety warnings
WARNING: Read all safety warnings, instruc-
tions, illustrations and specications provided
with this power tool. Failure to follow all instructions
listedbelowmayresultinelectricshock,reand/or
seriousinjury.

Makita DDF485RTJ Specifications

General

Drilling	Yes
Chuck type	Keyless
Built-in light	No
Product design	Pistol grip drill
Number of gears	-
Torque settings	21
Idle speed (max)	1900 RPM
Idle speed (min)	500 RPM
Chuck capacity (max)	13 mm
Chuck capacity (min)	1.5 mm
Sound pressure level	74 dB
Drilling diameter in wood (max)	38 mm
Drilling diameter in concrete (max)	- mm
Power source	Battery
Battery voltage	18 V

Weight and Dimensions

Depth	169 mm
Width	79 mm
Height	255 mm
Weight	1700 g