16
Load charts
(Mode A)
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Pounds
37.3 ft – 76.4 ft
22,000 lb Stationary
360˚
Feet
37.3 50.4 63.4 76.4
12
39,500
(65)
41,650
(72.5)
15
37,750
(59.5)
38,950
(68.5)
18,900
(73.5)
15,650
(77)
20
24,850
(49.5)
24,850
(62)
18,900
(68.5)
15,650
(73)
25
16,300
(36.5)
16,650
(55)
17,450
(63.5)
15,650
(69)
30
10,200
(12.5)
11,350
(47)
11,450
(58)
13,200
(65)
35
7650
(38)
7630
(52.5)
9280
(60.5)
40
4920
(25.5)
5020
(46)
6510
(56)
45
4490
(51)
Minimum boom angle (°) for
indicated length (no load)
39 46
Maximum boom length (ft) at 0°
boom angle (no load)
50.4
Boom
angle
Main boom length in feet
37.3 50.4
0°
10,050
(30.1)
3150
(43.2)
NOTE: ( ) Reference radii in feet. A6-829-103452A
#LMI operating code. Refer to LMI manual for instructions.
Main boom length in feet
Main boom
Lifting capacities at zero degree boom angle
Pounds
37.3 ft – 76.4 ft
22,000 lb
Pick and carry
up to 2.5 mph
Boom centered
over front
Feet
37.3 50.4 63.4 76.4
12
41,600
(65)
41,700
(72.5)
15
41,600
(59.5)
41,700
(68.5)
22,400
(73.5)
15,650
(77)
20
36,250
(49.5)
36,450
(62)
22,400
(68.5)
15,650
(73)
25
27,600
(36.5)
28,250
(55)
22,400
(63.5)
15,650
(69)
30
21,300
(12.5)
22,200
(47)
22,400
(58)
15,650
(65)
35
17,500
(38)
17,950
(52.5)
15,650
(60.5)
40
13,800
(25.5)
14,350
(46)
15,650
(56)
45
11,000
(39)
12,500
(51)
50
8360
(30)
9820
(45.5)
55
6240
(15.5)
7690
(39.5)
Minimum boom angle (°) for indicated length
(no load)
36
Maximum boom length (ft) at 0° boom angle
(no load)
63.4
Boom
angle
Main boom length in feet
37.3 50.4 63.4
0°
21,150
(30.1)
11,600
(43.2)
5790
(56.2)
A6-829-103453
#LMI operating code. Refer to LMI manual for instructions.
Main boom length in feet
Lifting capacities at zero degree boom angle
Main boom
NOTES:
1. Capacities are in pounds and do not exceed 75% of tipping loads as determined by test in accordance with SAE J765.
2. Capacities are applicable to machines equipped with 29.5x25 (34 ply) General tires at 76 psi cold inflation pressure.
3. Capacities appearing above the bold line are based on structural strength and tipping should not be relied upon as a capacity
limitation.
4. Capacities are applicable only with machine on firm level surface.
5. On rubber lifting with boom extensions not permitted.
6. For pick and carry operation, boom must be centered over front of machine, mechanical swing lock engaged and load restrained from
swinging. When handling loads in the structural range with capacities close to maximum ratings, travel should be reduced to creep
speeds.
7. Axle lockouts must be functioning when lifting on rubber.
8. All lifting depends on proper tire inflation, capacity and condition. Capacities must be reduced for lower tire inflation pressures. See
lifting capacity chart for tire used. Damaged tires are hazardous to safe operation of crane.
9. Creep – not over 200 ft of movement in any 30 minute period and not exceeding 1 mph.
To Next Page
Loading...
