Marantz DIGITAL PM730 - Rear Panel Connections; Tuner Inputs; Phono Inputs; CD;AUX Inputs

ENGLISH TEXT
FOREWORD
Your Marantz product has been specially prepared to comply
with the household power and safety requirements that exist
in your region. This product has a 4-position voltage selector
(110/120/220/240V) on the rear panel {A, N and T versions).
Since the voltage has been adjusted as shown below upon ship-
ment from the factory, please check the third alphabetical! letter
of the serial number and refer to the following table to note the
characteristics of the model in your possession:
SUFFIX VOLTAGE
A- 240V AC, 50/60 Hz
C— 120V AC, 60 Hz
U— 120V AC, 60 Hz
N- 220V AC, 50/60 Hz
T- 240V AC, 50/60 Hz
FOR UNITS SOLD IN THE UNITED
KINGDOM
Blue Brown
IMPORTANT
The wires in the mains lead are colored in accordance with the
following code:
Blue _ Neutral
Brown - Live
As the colors of the wires may not correspond with the terminal
identification in your plug, proceed as follows:
®@ Connect the brown wire to the terminal marked “L” or
colored brown or red.
® Connect the blue wire to the terminal marked '‘N” or colored
blue or black.
For 13A plugs, conforming to BS1363, use a 3A fuse.
For
other
plugs,
use
a
5A
or
lower
fuse
in
the
plug
or
adaptor
or
at
the
distribution
board.
NOTE FOR U.K.
Recording
and
playback
of
any
material
may
require
consent.
For
information,
please
refer
to
the:
Copyright Act 1956
Dramatic & Musical Performers Act 1958
Performers Protection Acts 1963 & 1972
and
to
any
subsequent
statutory
enactments
and
orders.
ABOUT THIS MANUAL
Refer
to
the
figures
given
on
page
1
and
2.
The
callout
nubmers
cor-
respond
to
those
found
in
this
manual.
All
references
to
the
con-
nections
and
controls
are
printed
in
BOLDFACE
type
as
they
appear
on
the
unit.
REAR PANEL CONNECTIONS
All connections to the rear panel should be made with the power
to the entire system turned off. To avoid confusion, connect one
cable at a time between the different components of your system.
This is the safest way to avoid cross-connecting channels or
confusing signal inputs with outputs.
(D TUNER INPUTS
For connection of the Line outputs of your tuner.
(2) PHONO INPUTS
For connection of a turntable with a magnetic phono cartridge.
(8) CD/AUX INPUTS
For connections of any high level signal source such as a tape
player, TV or Video sound source.
(4) TAPE 1/VIDEO, TAPE 2/EQ JACKS
It is possible to connect two tape recorders or a graphic equalizer
to these jacks. The IN jacks receive signals from the LINE OUT
jacks
of
the
cassette
deck,
and
the
OUT
jacks
feed
signals
to
the
LINE IN jacks of the cassette deck.
(5) PRE OUT
Output
terminal;
connected
to
the
input
terminal
of
a
power
amplifier.
© MAIN IN
Input
terminal;
connected
to
the
output
terminal
of
a
preampli-
fier.
The
preamplifier
output
and
main
amplifier
input
can
be
siparated
by
disconnecting
the
preamplifier
section
from
the
main
ampli-
fier
section
of
this
unit.
Do
not
remove
the
connector
wen
this
terminal
is
not
used.
(7) EASY OPERATION (E.0.) BUS TERMINAL
Connect
Marantz
stereo
components
equipped
with
an
§.O.
bus
terminal
(such
as
the
SD530,
SD630
or
$D430
tape
dick
and
ST530
stereo
tuner)
to
the
E.O.
terminal
using
the
gren
bus
cable.
Connecting
the
cable
to
any
terminal
other
than
he
E.O.
bus
terminal
will
cause
trouble
in
your
stereo
componeits.
The
easy
operation
bus
acts
as
a
remote
source
selector
for
th:
ampli-
fier.
Therefore,
you
need
not
operate
the
source
selecto;
switch
of
the
amplifier
when
you
change
and
use
source
programssuch
as
the
tuner
and
tape.
For
example,
with
conventional
systems,
when
you
want
to
listen
to
a
broadcast
while
playing
a
record,
you
must
switch
tte
func-
tion
switch
of
the
amplifier
to
TUNER
then
operate
th
-tuner,
With
the
E.O.
bus
system,
you
only
need
to
operate
the
tuier.
REMOTE CONTROL (R.C.) BUS TERMINAL
Connect the R.C. terminal of the PM630 or PM730 amnifiier to
the RC430 remote control receiver or other Marantz stero com-
ponent {such as the ST530 tuner or SD530, SD630 or D430
tape
deck)
equipped
with
an
R.C.
terminal
using
the
orange
remote control bus cable.
Pay
attention
to
the
color
terminals
when
connecting
tle
R.C,
cable.
Connecting
the
cable
to
any
terminal
other
than
tee
R.c,
terminal
may
cause
trouble
in
your
stereo
components.