Why can't I select EX/ES mode on my Marantz Stereo Receiver?
If you cannot select EX/ES mode, it might be because 'Surround center= NONE' has been selected in SPEAKERS SIZE SETUP or the input signal is incompatible. Make the correct setting and use a 5.1channel source.
Why does the remote control not work with my Marantz Receiver SR7300?
If you're experiencing issues controlling your Marantz SR7300 Receiver with the remote, consider these possibilities: 1. The batteries in the remote may be depleted. Try replacing them with new ones. 2. The remote controller's function-key setting might be incorrect. Select the correct position for the equipment you want to control. 3. You might be too far from the SR7300. Move closer to the receiver. 4. There could be an obstruction between the remote and the SR7300. Remove any objects blocking the signal.
Why is there no sound from the center speaker on my Marantz Receiver?
If your Marantz Receiver is not outputting sound from the center speaker, here are a few things to check: * Ensure the center speaker cable is correctly and completely connected. * If STEREO is selected for Surround mode, no sound will be output from the center speaker. Select a different surround mode. * If Center = NONE has been selected in SETUP mode, change to another Surround mode and make the correct setting.
Why are the surround speakers not working on my Marantz Receiver?
If your Marantz Receiver is not outputting sound from the surround speakers, consider the following: * Make sure the surround speaker cable is correctly connected. * If STEREO is selected for Surround mode, no sound will be output from the surround speakers. Choose a different surround mode. * If Surround = NONE has been selected in SETUP mode, select another Surround mode and make the correct setting.
Why is there no sound from the surround back speaker on my Marantz Receiver?
If your Marantz Receiver is not outputting sound from the surround back speaker, verify these points: * Ensure the surround back speaker cable is completely connected. * The surround mode must be set to EX/ES mode. Set surround mode to EX/ES. * Check if 'Surround back = NONE' has been selected in SPEAKERS SIZE SETUP. If so, make the correct setting.
Why is there no output to the subwoofer on my Marantz Receiver?
If you are not getting any output to the Sub Woofer Out on your Marantz Receiver, check if 'Sub-woofer = NONE' has been selected in SETUP mode. If so, select 'Sub-woofer = YES'.
Why can't I select Neo:6 mode on my Marantz Receiver?
If you cannot select Neo:6 mode on your Marantz Receiver, the input signal may be incompatible. Use a 2 channel Dolby Digital input signal, PCM input signal, or analog input signal.
Why can't I select CSII mode on my Marantz Receiver?
If you cannot select CSII mode on your Marantz Receiver, the input signal might be incompatible. Use a 2 channel Dolby Digital input signal, PCM input signal or analog input signal.
Why is my Marantz Receiver playing sound from the wrong input?
If your Marantz Receiver is outputting sound and pictures from equipment other than what's selected with the function selector, it could be due to an incorrectly connected input cable. Refer to the connection diagram and ensure the cable is connected correctly.
Why is there no sound from the surround back speaker on my Marantz SR7300?
If there's no sound from the surround back speaker, check these: * Ensure the surround back speaker cable connection is complete. * Confirm that the Surround mode is set to EX/ES. * Verify that 'Surround back = NONE' has not been selected in SPEAKERS SIZE SETUP; if so, make the correct setting.
General| Type | Stereo Receiver |
|---|---|
| Total Harmonic Distortion (THD) | 0.08% |
| Signal-to-Noise Ratio | 100 dB |
| Input Sensitivity | 200 mV |
| Headphone Output | Yes |
| Power Output | 100 W per channel (8 ohms) |
| Frequency Response | 10 Hz - 100 kHz |
| Input Impedance | 47k ohms |
| Digital Inputs | Coaxial, Optical |
| Analog Inputs | 6 |
| Analog Outputs | 1 |
| Tuner Section | AM/FM |
To Next Page
