Why surround mode cannot be changed on Marantz SR8000 Stereo Receiver?
If the surround mode cannot be changed on your Marantz Stereo Receiver, it may be because headphones are connected to the jack. Disconnect the headphones, as the surround mode will be fixed to STEREO when headphones are connected.
How to fix no output to Sub Woofer Out on Marantz SR8000?
If you are not getting any output to the Sub Woofer Out on your Marantz Stereo Receiver, check if "Sub-woofer = NO" has been selected in the SETUP mode. If it has, select "Sub-woofer = YES".
What to do if no sound is output from the center speaker of Marantz SR8000 Stereo Receiver?
If no sound is output from the center speaker of your Marantz Stereo Receiver, ensure the center speaker cable is correctly connected. Also, if STEREO is selected for Surround mode, no sound will be output from the center speaker; set another Surround mode. Verify that "Center = NONE" has not been selected in SETUP mode, and if it has, make the correct setting.
Why no sound is output from the surround speakers of Marantz SR8000 Stereo Receiver?
If you're not getting sound from the surround speakers on your Marantz Stereo Receiver, first, ensure the surround speaker cables are correctly connected. If STEREO is selected for Surround mode, no sound will be output from the surround speakers, so try setting another Surround mode. Also, check that "Surround = NONE" has not been selected in SETUP mode, and correct the setting if needed.
How to fix noise produced during DTS-encoded CD or laser disc play on Marantz Stereo Receiver?
To resolve the issue of noise during DTS-encoded CD or laser disc play on your Marantz Stereo Receiver, ensure that you perform a digital connection and select digital input before playing, as the problem may occur if analog input has been selected.
What to do if cannot get programmed station when the PRESET button is pressed on Marantz Stereo Receiver?
If you cannot get a programmed station when the PRESET button is pressed on your Marantz Stereo Receiver, it is possible that the preset data has been erased. Disconnecting the power plug for long periods of time will erase preset data. If this happens, input the preset data again.
Why a specific channel does not produce output on Marantz SR8000 Stereo Receiver?
If a specific channel does not produce output on your Marantz Stereo Receiver, verify the encoded channel on the source side to ensure that there is actually something recorded on that channel.
Why nothing appears on the remote commander display of Marantz SR8000 Stereo Receiver?
If nothing appears on the remote commander display of your Marantz Stereo Receiver, the batteries are likely consumed. Replace all the batteries with new ones.
Why DTS sources cannot be played on Marantz SR8000 Stereo Receiver?
If you cannot play DTS sources on your Marantz Stereo Receiver, it might be because the Surround mode is set to DOLBY. Try selecting another mode. It could also be that your DVD or LD player is not DTS digital out capable, so use a player which responds to DTS-digital out.
Why noise is heard during AM reception on Marantz Stereo Receiver?
If you're experiencing noise during AM reception on your Marantz Stereo Receiver, it could be due to interference from other electrical fields. Try changing the location where the AM indoor antenna is set up.
Tuner specifications for FM band.
Tuner specifications for AM band.
Audio performance and power ratings.
Video input/output specifications.
General unit specifications.
Included accessories.
Accesses tuner tracking memory and preset selection.
Verifies microprocessor and display functionality.
Tests various input/output signal paths.
Adjusts DC voltage at speaker terminals.
Adjusts quiescent current in power amplifier stages.
Diagnoses issues when the unit does not power on.
General| Brand | Marantz |
|---|---|
| Model | SR8000 |
| Category | Stereo Receiver |
| Language | English |
To Next Page
