To Next PageTo Next PageWhat to do if control with the remote control unit fails on Marantz SR8200?
If the remote control isn't working with your Marantz SR8200, first, replace all the batteries with new ones. Check if the remote controller's function-key setting is correct. Make sure you're not too far from the SR8200 and that nothing is blocking the signal between the remote and the receiver. If there is an obstruction, remove it.
What to do if no sound and picture are output even when power is on in Marantz Receiver?
If there's no sound or picture when your Marantz Receiver is on, first, check if mute is enabled and disable it using the remote. Then, verify that all input cables are correctly connected according to the connection diagram. Make sure the master volume isn't turned all the way down, and the function selector is in the correct position.
Why is there no sound output from the surround back speaker in my Marantz SR8200?
If you're not getting any sound from the surround back speaker on your Marantz Receiver, check the speaker cable connection to ensure it's correctly connected. Note that surround back channel is only active in THX surround EX mode, so set THX Surround EX mode. In other Surround modes, no sound will be output from the surround speaker. Also, verify that “Surr. Back = NONE” hasn't been selected in SETUP mode.
Why is there no sound from the center speaker on my Marantz SR8200 Receiver?
If there's no sound coming from the center speaker of your Marantz Receiver, first, ensure the center speaker cable is correctly connected. If STEREO is selected for Surround mode, no sound will be output from the center speaker, so select another Surround mode. Also, check that “Center = NONE” hasn't been selected in SETUP mode, and if it has, make the correct setting.
Why is there no sound coming from the surround speaker on my Marantz Receiver?
If you're not hearing sound from the surround speaker on your Marantz Receiver, check that the surround speaker cable is correctly connected. If STEREO is selected for Surround mode, no sound will be output from the surround speaker, so set another Surround mode. Also, ensure that “Surround = NONE” hasn't been selected in SETUP mode, and if it has, make the correct setting.
What causes noise during DTS-encoded CD or laser disc play in Marantz SR8200 Receiver?
If you're experiencing noise during DTS-encoded CD or laser disc playback on your Marantz Receiver, it might be because analog input is selected. Ensure you're using a digital connection, select digital input, and then try playing the source again.
Why can't I play DTS sources on my Marantz SR8200?
If you're unable to play DTS sources on your Marantz Receiver, it could be because the Surround mode is set to DOLBY. Select another mode. Also, the DVD or LD player might not be DTS digital out capable, so use a player which responds to DTS-digital out.
What to do if my Marantz SR8200 Receiver is outputting sound from the wrong channel?
If the sound from your Marantz receiver is coming from the wrong channel, check the speaker cable connections. Refer to the connection diagram to ensure the cables are correctly connected.
What causes my Marantz receiver to output sound and pictures from equipment not selected with the function selector?
If your Marantz receiver is outputting sound and pictures from equipment other than what's selected with the function selector, the input cable might be connected incorrectly. Connect the cable correctly by referring to the connection diagram.
What to do if player skips during play of a DTS source and produces noise on Marantz SR8200?
If your player skips and produces noise while playing a DTS source on your Marantz Receiver, it may be due to a data error during the skip. Set Surround mode to DTS-cinema or DTS-music.
General| Channels | 7.1 |
|---|---|
| Total Harmonic Distortion (THD) | 0.08% |
| Input Sensitivity | 200 mV |
| Signal-to-Noise Ratio | 100 dB |
| Tuner Section | AM/FM |
| Power Output | 110W per channel (8 ohms, 20Hz-20kHz, 0.05% THD) |
| Frequency Response | 10 Hz - 100 kHz |
| Digital Inputs | 2 x Coaxial, 2 x Optical |
| Digital Outputs | 1 x Optical |
| Surround Sound Formats | Dolby Digital, DTS |
| Video Inputs | 3 x Composite |
| Video Outputs | 2 (composite) |
