How to fix cloudy water in Master Spas Swimming Pool?
Cloudy water in your Master Spas Swimming Pool can be caused by dirty filters or inadequate filtration. Clean the filters with filter cleaner and adjust the filtration. It may also indicate unbalanced water chemistry, so you should test and adjust the chemical levels. If the water is old, drain the pool, clean the inner shell, and refill it with filtered water.
Why do I have eye or skin irritation in my Master Spas Swimming Pool?
If you notice eye or skin irritation while using your Master Spas Swimming Pool, it could be due to unsanitary water. Adjust the water chemistry based on testing results. It may also be caused by a total chlorine level above 5 ppm, in which case you should apply an oxidizer/non-chlorine shock treatment. Poor sanitizer or pH levels can also cause irritation, so adjust the pH level as necessary.
What to do if Master Spas MP Force Hot Tub water is deep blue or has colorful deposits?
A deep blue water color or colorful deposits precipitating from the water in your Master Spas Hot Tub can be caused by excessive buildup in the water from total dissolved solids, bather load, and chemical treatments over time, or it can be a reaction between substances in the water and excessive amounts of chemicals added to the water. Draining and refilling the water may be required to resolve this issue.
What causes foaming in Master Spas MP Force Hot Tub and how to fix it?
Foaming in your Master Spas Hot Tub is often due to high levels of body oils, lotions, soap, etc. Adding a small amount of defoamer can help to reduce the foaming.
How to remove scum ring around Master Spas MP Force?
A scum ring around your Master Spas Hot Tub is typically caused by a buildup of oils, dirt, and organic elements. Wipe it off with a clean towel and add an enzyme product to help prevent future buildup.
Why does my Master Spas Hot Tub have a strange water odor?
A water odor in your Master Spas Hot Tub can be caused by a few things. It may be due to low levels of sanitizer, so shock the water with a non-chlorine shock treatment or adjust sanitizer levels. The pH may be out of range, so adjust the pH level if needed. Another cause can be bacteria or algae growth, in which case you should adjust the sanitizer.
How to get rid of chlorine/bromine odor in Master Spas MP Force?
A chlorine or bromine odor in your Master Spas Hot Tub usually indicates excessive chlorine or bromine levels. Shock the water with a non-chlorine shock treatment to resolve this. Also, check the pH level and adjust it if necessary.
What to do if Master Spas MP Force Hot Tub causes eye or skin irritation?
If you experience eye or skin irritation from your Master Spas Hot Tub, it could be due to unsanitary water. Shock the swim spa with a non-chlorine shock treatment. Also, if the free chlorine level is above 5 ppm, allow it to drop below that level. Check your sanitizer and pH levels and adjust them according to your spa test strip results.
Key safety precautions for installation and use of the swim spa.
Warnings about suction entrapment hazards and their types.
Procedures for draining the swim spa using a submersible sump pump.
Instructions for cleaning and maintaining swim spa filter elements.
Steps for draining and winterizing the swim spa if not in use.
Electrical requirements for Configuration 3.
Electrical requirements for Configuration 5.
Introduction to the belt-driven propulsion system and its controls.
Detailed explanation of the swim spa control interface and its functions.
General| Seating Capacity | 6-7 |
|---|---|
| Weight (Dry) | 900 lbs |
| Insulation | Foam |
| Control System | Balboa |
| Voltage | 240V |
| Amperage | 50A |
| Shell Material | Acrylic |
| Warranty | 5 years |
| Heater | 4.0 kW |
| Lighting | LED |
| Filtration | EcoPur® Charge |
| Cabinet Material | DuraMaster™ Polymer |
To Next Page