43
AUGER ACCESS / AUGER TUBE CLEANING
7XUQRႇVPRNHUDQGDOORZWRFRROWRWRXFK
2. Unplug from wall.
5HPRYHFRRNLQJUDFNVZDWHUERZOJUHDVHGHÀHFWRUDQGKHDWGLႇXVHU
4. Cleanout any ash, pellets or debris in crucible.
5. Remove pellets from hopper.
6. Remove four screws holding pellet hopper to auger housing and remove hopper.
Reference Fig. 1 on page 42.
Tip: If connections to controller are limiting space, remove controller and disconnect connections to gain
PRUHDFFHVV5HIHUHQFH³&RQWUROOHU$FFHVV5HSODFHPHQW´LQVWUXFWLRQV7LHDSLHFHRIVWULQJWRSOXJVDWWKLV
VWHS7KLVZLOOPDNHFRQQHFWLRQVHDVLHULQIXWXUHVWHSV
7. Remove auger motor screw and nut (Fig. 4).
8. Pull auger motor from auger.
9. Remove auger bushing screw and remove auger bushing.
10. Remove auger from auger tube.
11. Using medium grit sand paper, sand outside of auger and inside of auger tube.
12. Using a vacuum clean out auger tube.
13. Insert auger into auger tube.
14. Insert auger tube bushing and assemble screw.
15. Push auger motor onto auger shaft and assemble screw and nut.
Tip:,IFRQWUROOHUZDVGLVFRQQHFWHGUHDVVHPEOH5HIHUHQFH³&RQWUROOHU$FFHVV5HSODFHPHQW´LQVWUXFWLRQV
16. Assemble pellet hopper to auger housing using four screws.
Cleaning is complete.
AUGER CHECK
7XUQRႇVPRNHUDQGDOORZWRFRROWRWRXFK
5HPRYHFRRNLQJUDFNVZDWHUERZOJUHDVHGHÀHFWRUDQGKHDWGLႇXVHU
3. Clean out any ash, pellets or debris in the crucible.
7XUQXQLWRQDQGSUHVVDQGKROGWKH6PRNH3ULPHEXWWRQXQWLO³3´LVGLVSOD\HGRQVFUHHQ
7KLVZLOOSXWVPRNHULQ³SULPHPRGH´ZKLFKZLOOURWDWHDXJHUFRQWLQXRXVO\XQWLOWKH6PRNH3ULPHEXWWRQ
is pressed again.
,IDXJHUGRHVQRWURWDWHFKHFNFRQQHFWLRQWRFRQWUROOHU5HIHUHQFH³&RQWUROOHU$FFHVV5HSODFHPHQW´
instructions.
5HSHDWFKHFNDIWHUVHFXULQJFRQQHFWLRQ,IDXJHUVWLOOGRHVQRWZRUNUHIHUHQFH³$XJHU$FFHVV$XJHU7XEH
&OHDQLQJ´LQVWUXFWLRQVWRHQVXUHWKHDXJHULVQRWMDPPHG
5HSHDWFKHFNDIWHUFOHDQLQJ,IDXJHUVWLOOGRHVQRWZRUNFRQWDFW0DVWHUEXLOW
Fig. 4
Auger
Motor
Auger
Bushing
Auger
To Next Page
Loading...
Need help?
General
