EasyManua.ls Logo

MasterCraft 62-3520-6 - User Manual

MasterCraft 62-3520-6
12 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
©2002, PRINTED IN U.S.A. 1000000947 (1/4/02)
62-3520-6
OWNER’S MANUAL
CONTRACTOR
Submersible
Sump Pump
MD
Installation/Operation/Parts
For further operating, installation,
or maintenance assistance:
Call 1-877-455-5508

Table of Contents

Questions and Answers

  • B
    Barbara CollinsAug 5, 2025
    What to do if my MasterCraft 62-3520-6 Water Pump motor does not run?
    • A
      alejandro47Aug 5, 2025
      If your MasterCraft Water Pump motor isn't running, there are several potential causes. First, check for a blown fuse and replace it if necessary. Also, check if the circuit has tripped and reset it. Ensure the plug is properly connected and clean the prongs if they are corroded. Verify adequate water level and add water if needed. Allow the pump to cool in case of overload. Inspect the switch, adjusting the float or replacing the switch if defective. If none of these steps work, the motor may be defective, requiring pump replacement. Finally, check the float position, referring to the Automatic Float Switch section.
  • B
    Brandon CooperAug 14, 2025
    How to fix a MasterCraft 62-3520-6 when the motor hums but there is reduced or no flow?
    • D
      David NelsonAug 14, 2025
      If your MasterCraft Water Pump motor hums but the flow is reduced or non-existent, the impeller might be jammed. Unplug the pump and unclog it. Another possibility is a plugged check valve, which you should also unplug the pump to unclog. A blocked screen could also be the issue; unplug the pump and clean the screen. Check for line leaks and unplug the pump to repair them. A worn impeller could also cause this problem, so unplug the pump and replace the pump impeller. If these steps don't resolve the issue, the motor itself may be defective, requiring you to replace the pump.
  • T
    Tiffany RiosAug 25, 2025
    Why does my MasterCraft Water Pump run continuously?
    • A
      Amanda Morris DVMAug 25, 2025
      Your MasterCraft Water Pump might run continuously due to a plugged screen. Unplug the pump and clean the screen. Alternatively, a defective switch could be the cause, requiring switch replacement. Also, check for a float obstruction referring to the Automatic Float Switch section.

Summary

Safety Instructions and Operation

Understanding Safety Alert Symbols

Explains DANGER, WARNING, and CAUTION symbols for injury prevention.

Electrical Safety Precautions

Details hazardous voltage, grounding, and GFCI outlet requirements.

Pump Operation Details

Describes automatic float switch activation and deactivation water levels.

Technical Specifications

Lists power supply, motor duty, temperature, and circuit requirements.

Installation Guide

Pump Installation Steps

Provides step-by-step instructions for installing the sump pump in the sump pit.

Automatic Float Switch Setup

Details the installation and adjustment of the automatic float switch.

Operational Check Procedure

Outlines how to test the pump's operation after installation.

Troubleshooting Common Issues

Motor Not Running

Diagnoses causes and provides corrective actions for a non-operational motor.

Reduced or No Flow

Identifies probable causes for low flow or no discharge.

Pump Runs Continuously

Addresses issues where the pump fails to shut off.

Repair Parts List

Component Identification

Diagram showing numbered pump components for easy identification.

Part Number Cross-Reference

Lists repair parts with part numbers and quantities for ordering.

MasterCraft 62-3520-6 Specifications

General IconGeneral
BrandMasterCraft
Model62-3520-6
CategoryWater Pump
LanguageEnglish

Related product manuals