Maximum Controls MAX 1500 - BC-7 Module LED Troubleshooting

RESET
GATE
OPEN/
CLOSE
GATE
SHUT
OFF
ON
/
OFF
Bat
t
er
y
EF1
/2
B
attery Vo
ltag
e
R
epl
ac
e
Batt
er
y
TEST
Batt
er
y
Batt
er
y IN
Er
r
o
r
M
AX BC-
7
Ba
tte
ry
Module
BATTERY
I
N
POW
ER/
SO
LA
R
I
N
POW
ER
IN
Ba
t
t
er
y
Pack
TO MOTOR
CONTRO
LL
E
R
w
w
w.Max.
U
S.com
BATTERY
IN
POWER/SO
LA
R
IN
IMPORTANT
connect to
“BATTERY IN”
be
f
ore use
E1/2
Ba
t
t
e
ry
Volta
g
e
Re
p
la
c
e
Ba
tte
r
y
ON/OFF
Batter
y
T
E
ST
Ba
tt
e
ry
Ba
tt
e
ry IN
E
rror
F
M
A
X
B
C-7
Ba
t
tery
Modu
l
e
ON/OFF
Battery
EF1/2
Battery Voltage
Replace
Battery
TEST
Battery
Battery IN
Error
MAX BC-7
Battery Module
ON/OFF
Battery
POWER
O
N
OFF
To Turn OFF ALL POWER:
1 Turn OFF AC POWER switch on MAX Toroid.
Battery power remains ON.
2 Press and HOLD ON/OFF BATTERY button on
MAX BC-7 until 4 LEDs turn ON, release button.
3 WAIT for ALL LEDs to turn OFF. Up to 30 sec.
ON
/
OF
F
B
a
tt
e
r
y
POWE
R
O
N
OFF
To T
urn OFF ALL POWER:
1
Tu
rn
O
FF
AC PO
WER sw
it
c
h
o
n
MAX
T
o
r
o
id.
Ba
t
t
ery po
w
er r
e
ma
in
s
O
N.
2
Pr
ess and HOL
D
ON/
O
F
F BATTERY
button o
n
M
AX BC-7
u
ntil 4
L
EDs
turn ON, release but
ton
.
3
WAIT
for ALL
L
EDs
t
o tur
n
OFF.
Up
to
3
0
s
e
c
.
BC-7 LED
Problem Condition
Normal
LED
Solution(s) for
Problem Condition
• Battery is very LOW. Check if AC power ON/OFF switch is ON. If so, check AC power.
• “BATTERY Plug” not plugged in to “BATTERY IN” port on battery module (see below).
• Battery needs to be replaced if BATTERY TEST fails and “REPLACE BATTERY” LED is ON.
“BATTERY VOLTAGE (E 1/2 F)” LEDs, only “E” is ON.
“BATTERY IN ERROR” LED is ON.
“REPLACE BATTERY” LED is ON.
1
OFF
3
OFF
2
Battery IN Error LED: Lights when there is a battery
connection problem. Make sure battery plug #1 is plugged
into BATTERY IN port or there is no damaged or loose wires.
TEST Battery Button: Press to show amount of battery power
available when using battery power ONLY (Battery voltage
LEDs will light respectively).
Replace Battery LED: Replace battery when lit.
BATTERY Plug:
MUST be plugged
into “BATTERY IN”
port Before use.
POWER/SOLAR IN Port:
MAX Megatron Toroid
box connection.
POWER IN / Battery Pack Ports:
Back of MAX MC-200 motor
controller connections.
ON/OFF Battery Button:
IMPORTANT: Battery power automatically turns ON when MAX
Megatron Toroid Box AC POWER Switch is turned ON.
To turn OFF ALL POWER to operator:
1. Turn OFF AC POWER Switch on MAX Megatron Toroid Box.
Battery power remains ON.
2. WAIT for 15 seconds.
3. Press and HOLD (approx. 5 seconds) the RED ON/OFF BATTERY
button until MAX BC-7 LEDs turn ON, then release button.
LEDs will turn OFF. (Up to 30 sec.)
BC-7 module LED troubleshooting
3. BATTERY IN ERROR
2. REPLACE BATTERY
1. BATTERY VOLTAGE
20
UL 325 2016 Standard-MAX Quick Install Rev 8