Why I barely see any hair reduction with Me Hair Removal System?
Hair reduction results vary depending on the treated body area and adherence to instructions. Ensure you are following the suggested protocol and treatment duration.
Why are no flashes coming out of my Me Smooth Hair Removal System?
If your Me Hair Removal System isn't flashing, ensure an energy level is selected, the activation button is pressed, and the RF chrome skin contact bars are fully touching your skin in the treatment area. All three conditions must be met for the system to flash.
Is it normal to feel warmth when using Me Smooth Hair Removal System?
Yes, it’s normal to feel warmth, tingling, or itching when using the Me Hair Removal System. This discomfort and warmth should be up to moderate.
How to fix no lights on my Me Smooth Hair Removal System?
If no lights are on, it likely means the power cable isn't connected. Connect the power cable.
Why is the accessory activation button on the base of my Me Smooth flashing?
If the accessory activation button on the base is flashing, the accessory slot is empty. Insert the protective cap.
Why are all the pulse indicators blinking on my Me Hair Removal System?
If all indicators for the percentage of pulses remaining (100%- 50%-Empty) are blinking, it means the cartridge slot is empty. Insert a cartridge or a protective cap.
Why is the “Empty” indicator constantly on on Me Smooth?
If the “Empty” indicator is constantly on, it means there are no more pulses remaining in the cartridge. You need to insert a new cartridge.
Why is the activation button on the applicator of my Me Hair Removal System blinking?
If the activation button is blinking, it means an energy level was selected, but the activation button hasn't been pressed yet. Press the activation button. The applicator fan will then start blowing, indicating that the cartridge is active.
Why are all energy setting buttons blinking on my Me Hair Removal System?
If all the energy setting buttons (High-Medium-Low) are blinking, it means that no energy level has been selected. Select an energy level to proceed. Once selected, the applicator fan will start, indicating the cartridge is active.
What to do if my skin is red after using Me Smooth?
Redness can occur after treatment with the Me Hair Removal System and usually disappears within 24 hours. If the redness lasts longer than 24 hours, discontinue use.
Defines the intended use of the mē system for hair removal, covering skin tone, hair color, and body areas.
Lists the items included in the mē system package.
Identifies and describes the main components of the mē system based on Figure 1.
Details the components of the applicator part of the mē system with reference to Figure 2.
Lists specific conditions and situations where the mē system should not be used due to safety risks.
Provides crucial warnings about device usage, handling, and potential hazards like electric shock and overheating.
Emphasizes keeping the device away from children and outlines precautions for sensitive skin and hair color.
Lists rare but possible side effects of using the mē system and advises consulting a doctor.
Provides step-by-step instructions for setting up the mē system before first use.
Details the procedure for performing a skin sensitivity test before full treatment.
Outlines skin preparation, device setup, energy level selection, and initial pulse emission.
Explains the correct gliding motion for treatment and provides tips for effective coverage.
Provides a recommended schedule for treatments to achieve optimal hair removal results.
Instructions for cleaning and storing the mē system to maintain its condition.
Advises on how to care for the skin after treatment, including sun exposure warnings.
Step-by-step instructions for removing and replacing the elōs cartridge in the applicator.
Details proper disposal of used elōs cartridges and protective cap usage.
Information on using the mē system internationally, including voltage and travel accessories.
Explains what different indicator lights mean and how to troubleshoot common device errors.
Addresses issues related to accessory slots, cartridge status, and skin reactions post-treatment.
Outlines the warranty terms, coverage, and limitations for the mē device.
Covers responsibilities for shipping costs and intellectual property rights related to the document.
Provides details about the manufacturer, Syneron Beauty Ltd., and their intellectual property rights.
Interprets the various labels and symbols found on the mē system's nameplate.
Lists the technical specifications, safety standards, and EMC standards the device complies with.
Details the temperature, humidity, and altitude requirements for storage and operation.
Provides contact details for customer support and further information about the mē system.
General| Brand | Me |
|---|---|
| Model | Smooth |
| Category | Hair Removal System |
| Language | English |
To Next Page
