EasyManua.ls Logo

Measuretek PS-102-75 - User Manual

Measuretek PS-102-75
18 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
WWW.MEASURETEK.NET
PS-102
User/Technical Manual
Contents subject to change without notice
Version 1.0
08/2013

Table of Contents

Other manuals for Measuretek PS-102-75

Preview: Operation Manual
Operation Manual10 pages

Questions and Answers

  • B
    Beth MorrisAug 13, 2025
    Why is weighing not accurate on my Measuretek Scales?
    • F
      fkleinAug 13, 2025
      If your Measuretek Scales are not weighing accurately, it could be due to several reasons. First, check for any objects stuck between the load cell and the scale base and remove them. Second, the load cell might have received a heavy impact, in which case you should perform a Linearity calibration. Next, if the scale is not near Chicago, loosen the shipping protection screws. Finally, ensure the load is placed in the center of the weighing platform.
  • M
    Melissa WilsonAug 17, 2025
    How to fix Measuretek Scales that does not turn on?
    • L
      Lisa SantanaAug 17, 2025
      If your Measuretek Scales do not turn on, there could be a few reasons: * The AC adapter might not be securely connected. Try re-plugging it or rotating the plug. * The batteries may be low. Replace them with new ones. * The indicator might be damaged. If so, replace it and perform a calibration.
  • L
    Lauren MarksAug 20, 2025
    What to do if I cannot zero the display on my Measuretek Scales?
    • A
      Angela CallahanAug 20, 2025
      If the display on your Measuretek Scales cannot be zeroed, it could be due to these reasons: 1. The load on the scale might exceed allowable limits. Remove some of the load. 2. The load on the scale might be unstable. Wait for it to stabilize, then press the ZERO/ON/OFF key.
  • N
    Nicole CarpenterAug 25, 2025
    What does '0 ???' mean on Measuretek PS-102-75 and how to fix it?
    • N
      Nicholas GutierrezAug 26, 2025
      If your Measuretek Scales display shows '0 ???', it might be due to the following reasons: * The indication is out of the key zero range. Reduce the weight on the platform until the indication is within the key zero range. * The weight reading is below the Power On Zero limit. In this case: 1. Install the platform on the scale. 2. Loosen the shipping protection screws. 3. Check for any objects stuck between the scale base and remove them. 4. Perform zero calibration.
  • M
    michael97Aug 28, 2025
    What does 'CAL.Er' mean on Measuretek PS-102-75 and how to resolve it?
    • S
      Steven FrazierAug 28, 2025
      If your Measuretek Scales display shows 'CAL.Er', it could be due to these reasons: * The input data or loaded weight is either too small or too big. Input correct data and load the correct weight onto the platform. * The weight signal is unstable or un-linear. In this case, return the scale for repair.
  • N
    Nicholas HollandAug 31, 2025
    What does 'EEP.E1' mean on Measuretek PS-102-75 and how can I fix it?
    • R
      Ryan MedinaSep 1, 2025
      If your Measuretek Scales display shows 'EEP.E1', it could be due to: * CONFIG parameters not correctly set. Reset CONFIG parameters per the Technical Manual. * CAL parameters not correctly set. Perform calibration.
  • L
    Lee PriceSep 5, 2025
    What does 'Ad ???' mean on Measuretek PS-102-75 and how to troubleshoot it?
    • R
      Robert MillerSep 5, 2025
      If your Measuretek Scales display shows 'Ad ???', it could be due to: * The cable from the platform to the indicator is not correctly connected, disconnected, or short circuiting. Replace it with a new indicator and perform calibration. * The indicator is damaged. Return the scale for repair.
  • M
    Matthew RossSep 8, 2025
    What does 'EEP.E2' mean on Measuretek PS-102-75 and how do I fix it?
    • J
      Jessica RossSep 8, 2025
      If your Measuretek Scales display shows 'EEP.E2', it means the USER parameters are not correctly set. You should reset the USER parameters per the Technical Manual.

Measuretek PS-102-75 Specifications

General IconGeneral
BrandMeasuretek
ModelPS-102-75
CategoryScales
LanguageEnglish

Related product manuals