Specification
6
Output Voltage (max.)
60 kV r.m.s. (30 kV – 0–30 kV) at 61,8 Hz
Parameters of Standard Test Specifications
Display Dot-matrix liquid crystal display giving alpha-numeric information
and kV test voltage to two digits.
Temperature Range
Operation 0 °C to + 40 °C
Storage –30 °C to +65 °C
Humidity Range
Operating 80% RH at 40 °C (non-condensing)
Storage 93% RH at 40 °C, 95% RH at 25 °C cyclic
(in accordance with BS 2011 Part 2–1)
Input Socket Battery charger or 12 volt vehicle supply inlet socket.
Safety The test set meets the requirements for safety to IEC 1010-1
(1995), EN61010 (1995). The safety interlock is to BS 5304
(1988) ‘Guarding of Machinery’ standard.
E.M.C. In accordance with IEC 61326 including amendment No. 1
Power Supply Internal rechargeable 12 V, 12 Ah, battery (typically 12 hours
continuous testing). Charger supply 90 V to 264 V, 50/60 Hz.
12 volt, negative to chassis, vehicle lead set (does not recharge
internal battery)
Fuses 2 x F6, 3 A, IEC 127/1, 20 mm x 5 mm, HBC fuses.
Dimensions 373 mm x 259 mm x 247 mm (14
11
⁄16 in x 10
3
⁄16 in x 9
3
⁄4 in) basic
without accessories.
Weight 19 kg (42 lb) basic without accessories.
Cleaning The exterior case can be wiped with a clean cloth dampened with
an alcohol based cleaning fluid.
Test Specifications Parameters
Test Spec. Initial Rate of rise Intermediate Intermediate Number Maximum Test Results
Stand of Test Stir Stand of Time
Time Voltage Time Time Tests
5 min test 1 min. 2 kV/s 30 s 30 s 3 4 min. 30 s Mean
BS 148 etc. 3 min 2 kV/s 1 min 1 min 6 16 min Mean
IEC156 5 min. 2 kV/s optional 2 min 6 18 min. Mean
EN 60156 5 min 2 kV/s optional 2 min 6 18 min Mean
ASTM D877 2 min. 20 s 3 kV/s - 1 min. 5 8 min. Mean
ASTM D1816 3 min. 0,5 kV/s Continuous 1 min. 5 17 min. Mean
UNE21 10 min 2 kV/s 1 min. 4 min. 6 38 min. Mean of last 5 tests
Withstand ‘A’ 2 kV/s Ramps to preselected value for 1 minute or breakdown
Withstand ‘B’ 2 kV/s As above and continues to breakdown or maximum value of test set
Withstand test at 22 kV, 30 kV or 40 kV (depending on
equipment category and electrode gap) for 1 min If break-
down occurs another two tests are carried out, both must
pass for sample to be accepted.
As per BS5730a but ramps to Breakdown after test is
passed.
BS148 etc. includes BS 5874, VDE 0370, NFC 27, CEI 344, ΓOCT 6581, SABS 555, AS 1767, STAS 286 and IP 295.
NFC 27, STAS 286 and UNE 21 omit the first breakdown value from the average calculation.
BS5730a - 2 kV/s 1 min. 1 min.
BS5730a LEPLC 1min stir + 2 kV/s 1 min. 1 min.
1 min stand
To Next Page
Loading...
Need help?
General
