REAR PANEL: Controls & Features (Continued)
RECTIFIER SELECT: Diodes / Tube RectifierTracking (Continued)
world to the high gain preamp, power clip char-
acteristics were the only way to get a heavier sound. As the power section tries to draw more current at higher volumes, the tube
rectifiers begin to sag and compress the sound while scooping the harder midrange frequencies, creating an ultra expressive power
signature. Solid state rectifiers do the opposite and deliver a steady, stiff supply of current - enabling the power section to crank out
its rated wattage with immediate response and tight authority.
TUBE TRACKING would likely be the choice for single note soloing where each
note morphs through the vowel sounds as the dynamic content changes from
attack to decay. The SILICON DIODES will keep bass frequencies tight and track
better at extreme preamp gain settings, especially when detuned or at higher
volumes, and emphasize attack and urgency.
The Switchable Rectifier feature is a huge part of the success of our entire Dual
Rectifier line and has elevated them to their current status as iconic classics.
The removable “Euro” Style” A.C. cord that is supplied with your new Stiletto makes set-ups and tear-downs
after the gig a snap. It also makes de-racking much easier when you wish to remove the unit from a hard wired rack system where all
the A.C. cords have been cable-tied in. Additional heavy duty cords are available should you
ever need one...simply call us direct and we can ship one directly to you for a nominal charge,
plus shipping cost. Make sure the A.C. cord is firmly seated in the
A.C. RECEPTACLE before
powering up the amplifier.
NOTE: Never alter the three prong power cord in any way.
This is the A.C.’s (Alternating Current) main fuse and provides protection from outside A .C. fluctuations as well as power
tube failure damage. Should the Fuse blow, replace it with the same rating in a Slo-Blo type package. The domestic U.S. version
requires a 4 amp ( Stiletto Trident ) Slo-Blo fuse. A power tube short or failure is often the cause of a blown fuse...Follow the cold
start procedure mentioned in the ON/STANDBY switch section and watch the power tubes as you flip the STANDBY to the ON position.
If a power tube is going bad or is arcing you will see it! Flip the STANDBY switch to Standby
immediately and replace the faulty power tube and the fuse if necessary.
If you see nothing abnormal as you lift the STANDBY switch, it is possible that a power tube
shorted temporarily and blew the Fuse. If this is the case it may work again normally. To be
safe, you might want to replace it and just the adjacent tube or all power tubes in the “shotgun”
troubleshooting tradition and save the replaced set as spares. Spare fuses are a must for the
fabled cord bag along with your spare tubes. Always carry both for they could be worth their weight in gold someday.
That covers the features and functions on the Rear Panel and by now you should be ready to start crafting your dream Tone. If you
would like some examples of ways to set the modes in your Stiletto for different applications, you may find the following SAMPLE
SETTINGS helpful.
We wish you a lifetime of amazing and inspirational Tone from your new musical instrument and our hope is that it takes you to new
and exciting places on your musical journey.
WARNING: Unplug power
before replacing fuse or
removing bolts mounting
chassis
FUSE
POWER FUSE
120 V~
60 Hz
4 A
4 A
SLO
BLO
OOGIE
B
M
ESA
The Spirit of Art in Technology
FUSE
POWER FUSE
120 V~
60 Hz
4 A
4 A
SLO
BLO
WARNING: Unplug power
before replacing fuse or
removing bolts mounting
chassis
OOGIE
B
M
ESA
The Spirit of Art in Technology
PAGE 15
SEND
SEND LEVEL
LOOP IN
SILICON
DIODE
CH 2 CH 1
TUBE
RECTIFIER
TRACKING
FX LOOP
To Next Page
Loading...
